Question about 1996 Ford Crown Victoria

1 Answer

How do i replace the solenoid only?

Can i replace the solenoid without replacing the starter?

Posted by yodagurl78 on

Ad

1 Answer

Stephen

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 21,873 Answers

You could but most people replace both at the same time. The solenoid is not cheap, and if one is going bad the other is in the same condition and age.

Posted on Jul 30, 2012

Ad

2 Related Answers

James Young

  • 4044 Answers

SOURCE: Replaced starter 3 times. Replaced starter

Sounds like the Flywheel is damaged or out of alignment and it is causing a bind. Check your flywheel.

Posted on Sep 20, 2010

Ad
Mr BrokRench

Mr BrokRench

  • 1623 Answers

SOURCE: 1966 mustang 289. won't start,

Ignition problem... No signal from ignition to solenoid...run a starter draw test to confirm starter is ok --- You can run your jump wires to a remote starter button or switch to get around it for now.

I hope this helps.

Posted on Sep 22, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the starter ,alternator ,main fuse,and new battery ...and I'm not getting any fire from the battery to crank it ....does anyone know what this problem is ??? ////98 ford explorer


Check the starter solenoid and the connections from the battery to ground, battery to fusebox, ignition key switch, neutral or park safety starting switch, solenoid, and solenoid to starter. Make sure you have ignition key switch wires connected to the solenoid - without them - the solenoid can not close to send 12V to the starter.

Nov 02, 2015 | Ford Cars & Trucks

2 Answers

97 Nissan Pathfinder starter coils what do they look like


Replace the starter. It's not a coil, it's the solenoid. You can't get it without the starter.

Jul 11, 2015 | Nissan Cars & Trucks

1 Answer

Replacing the starter solenoid on a '07 Honda CRV


No. the solenoid has a plunger that hooks onto the arm that pushes the pinion into the ring gear just before the starter motor starts to spin. There is an adjustment at the pivot that has to be set for the new solenoid

Nov 06, 2013 | 2007 Honda Accord Sedan

1 Answer

I have just replaced a starter on a 2000 ford contour and when I put battery cables back on, the starter was rotating without the key


Seems your solenoid is activated or jammed. If the solenoid is part of(mounted on) the starter, it's a bad starter. Take the small ignition (starter) wire from your solenoid, it should only be hot (have power ) in the start position. The starter shouldn't turn with it removed. BobB

Sep 21, 2013 | 2002 Chevrolet Impala

1 Answer

When replacing battery on 93 buick, starter engages


were you trying to start it before you removed the other battery?
if so the solenoid is stuck.
turn the key on and hook up the battery and let it start then turn the key off and let it die. the kick of it starting should knock the solenoid back like it should be. if it keeps trying to start you will have to pull the starter and replace the solenoid

Jan 25, 2013 | 1993 Buick Regal

1 Answer

Can I change the solenoid on my 1992 Dodge Dakota pickup, 6 cyl without removing the starter or do I have to replace the whole starter?


Most starters now a days have the solenoid integrated into the starter and are therefore irremovable. Replace the whole starter.

Dec 05, 2011 | 1992 Dodge Dakota

1 Answer

When I turn the key it clicks several times and then starts. After it is warm it starts without clicking


this sounds like you have a problem with the starter solenoid contacts in the solenoid.change the starter motor as it comes with the solenoid and the starter sometimes goes bad afterwards.or you can buy just the solenoid and replace it alone.

Nov 08, 2011 | 1995 Dodge Dakota

1 Answer

It wont start. Buying a starter but was told it might be the "cylnoid"?


Buying a solenoid without a starter is the same as buying a hamburger without the bun. The solenoid sits on top of the starter in a GM and they come out and go in as a pair. If you go in to buy a new starter it should have a new solenoid already on it. Replacing one without the other pretty much guarantees that you will be doing this job again a few months down the road for the part you didn't do this time. Hope this helps.

Aug 18, 2011 | 2001 Pontiac Sunfire

2 Answers

The selinoid on my truck is gone again I had the starter rebuilt and new selinoid put on about 9 months ago. Why? Can I replace selenoid without taking starter out? Thanks


no u must remove the starter, as far as the reason i suspect they did something wrong or used sub standard solenoid repair parts

Oct 26, 2010 | 1996 Chevrolet C/K 2500

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...