2002 mpv left rear electric door lock clicks with switch but doesn't lock or unlock.

Power Door Lock Operation
The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door, but the rear integration module (RIM), which is the master control for the door lock system, determines when the lock functions are permitted. The RIM receives and examines the requested lock function from the individual door modules, or from the remote function actuator (RFA) via the class 2 serial data circuit. The RIM also examines the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. If the RIM determines that a lock or unlock function is permitted, it sends a class 2 message back to the individual door modules commanding them to perform that Lock or Unlock function.
Power Door Lock Components
The power door lock system consists of the following components:
?€¢
Driver door lock switch

?€¢
Passenger front door lock switch

?€¢
LH rear door lock switch

?€¢
RH rear door lock switch

?€¢
LH middle door lock switch (w/ V4U)

?€¢
RH middle door lock switch (w/ V4U)

?€¢
Driver door switch assembly (DDSA)

?€¢
Driver door module (DDM)

?€¢
Passenger front door module (PDM)

?€¢
LH rear door module (LRDM)

?€¢
RH rear door module (RRDM)

?€¢
Left middle door module (LMDM) (w/ V4U)

?€¢
Right middle door module (RMDM) (w/ V4U)

?€¢
Driver door lock actuator

?€¢
Passenger front door lock actuator

?€¢
LH rear door lock actuator

?€¢
RH rear door lock actuator

?€¢
LH middle door lock actuator (w/V4U)

?€¢
RH middle door lock actuator (w/ V4U)

?€¢
Driver door cylinder unlock switch

?€¢
Rear integration module (RIM)

?€¢
DRVMDL fuse (10-amp)

?€¢
PASS MDL fuse (10-amp)

?€¢
RRDR MDL fuse (10-amp)

?€¢
Class 2 serial data link

Sounds like your door module is the issue. You can try to disconnect the battery for 5-10 minutes then retry or GMC to see if there is a recall.

coulb be the control switch on your panel you can take the door panel off and check for loose connections and try to test for continuity. if you dont know how take it to a shop and have them diagnose the electrical. im quite sure it the switch that burnt out

change the drivers side door lock mechanism ,its a complete unit full of fancy electronics

I assume the doors can be manually locked. The problem is in the electrical circuit. That means anything from a faulty switch (the lock / Unlock button) to a loose connection. If both switches don't work then look for a blown fuse. If one switch works and the other doesn't than remove the switch and inspect its connection. If it's ok then check the switch. If both switch and connections are OK then you'll have to remove the door panel and access the lock mechanism.

Either a fuse problem or could be a twist in the electrical cable in the door joint . Sometimes chafes the outer core away and causes shorts in stuff like this .

check fuses. I have a button that unlatches the back glass that is up by the instrument panel. I pushed that button a million times. Then I realized that the cab lights weren't working so I replaced the fuse, which happened to fix the back door!

12V CONSTANT WIRE RED and PINK/BLACK Ignition harness
12V IGNITION WIRE DARK BLUE Ignition harness
12V ACCESSORY WIRE BLACK/ORANGE Ignition harness
STARTER WIRE YELLOW Ignition harness
PARKING LIGHTS (+) BLACK/YELLOW At Headlight switch
POWER DOOR LOCK (5-wire reverse polarity) ORANGE/PURPLE Harness Coming Into Vehicle From Driver's
Door
POWER DOOR UNLOCK (5-wire reverse
polarity)
PINK/PURPLE Harness Coming Into Vehicle From Driver's
Door
DOOR TRIGGER (-) YELLOW/BLACK At Headlight Switch
DOMELIGHT SUPERVISION (-) Use door trigger
TRUNK TRIGGER (-) GRAY/BLACK At Light In Trunk
TACHOMETER WIRE TAN/BLUE or BLACK/GRAY At Ignition Coil
BRAKE WIRE (+) WHITE/BROWN At Brake Pedal Switch
HORN TRIGGER (-) BLACK/RED Harness Coming From Steering Wheel At
Column
CAUTION! SRS airbag wires are not enclosed in protective loom at the steering column. They are a twisted pair of wires that run with rest of
ignition harness. Be careful not to cut or probe these wires.

Radio:

(Black plug)
Rear Right speaker -: Blue w/White stripe
Rear Left speaker -: Brown w/Yellow stripe
Front Right +: Purple
Front Left +: Dark Green
Rear Right speaker +: Blue w/Orange Stripe
Rear Left speaker +: Brown w/Blue Stripe
Power Antenna/Amp: White
(Gray Plug)
+12v battery wire: Pink or Pink w/White Stripe
+12v Ignition wire: Red w/ White Stripe
Front Right speaker -: Blue w/ Red Stripe
Front Left speaker -: Brown w/ Red Stripe

Courtesy of: forums.mazdaworld.org

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done