2006 Hyundai Sonata Logo
Posted on Dec 10, 2008

Cant remove the bulb from the inside

How do i remove the third brake light bulb from the housing in the car in a 06 hyundai sonato..

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 3 Answers
  • Posted on Dec 19, 2008
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Dec 19, 2008
Answers
3
Questions
0
Helped
2404
Points
6

According to the service manual, you must remove the cloth package tray that the third brake light assembly is attached to. First unclip the electrical connector located directly underneath in the trunk. Then remove the five philips screws securing the tray to the rear body by folding down the rear seatbacks. The package tray must then be pried off-not easy.

  • Anonymous Dec 19, 2008

    Just found this on WIKI...seems much easier (must replace mine as well)...1.) unplug the connector in the trunk.

    2.) remove the 2
    gold-colored screws from inside the trunk. They can be seen from the
    trunk. 1 is thru the larger square opening where the wire connects to
    the 3rd brake light. The 2nd is on the right side thru a small
    (screwdriver width) hole covered by a piece of foam tape stuff.

    3.) after removing the 2 screws, go inside the cabin and the brake light housing pops right up.

    4.) disconnect the bulb from the housing while inside the cabin.

    5.) in the trunk remove the wire and bulb. (it's about 5 inches long. the wire from the connector to the bulb socket)

    6.) reverse steps to install.



×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer
0helpful
1answer

I need to replace a third brake light bulb on my 2011 hyundai sonata gls the diy way

Remove the rear seat. Remove the rear package tray. Unsnap the center mounted tail light. Replace bulb
0helpful
1answer

Can I just replace the third brake light bulb only ..just the bulb.on a 2005 Chevy Malibu LS.or do I have to replace the hole brake light itself..

from inside the trunk looking up at the light First, gently work the gray, carpet like cover loose from the area around the tail light ,(this may give you a little trouble). Once you have done this, you will see three silver nuts. These must be unscrewed. The lower left nut must be accessed through a hole next to where the trunk lid fits. (The screws are permanently attached to the lens housing so will not drop into obscurity when the nuts are removed). After removing the nuts, GENTLY work the lens housing away from the car. You may need a screw driver to unseat the housing, but just be gentle.

You will find three bulbs inside the lens. The brake light bulb is on the lower right side. Simply pull the old bulb out and insert the new one.

Just reverse these directions to reassemble the housing.
0helpful
1answer

Third brake light

stand on truck bed.the cargo lamp housing held in place by two screws.just remove the two screws holding cargo lamp housing replace bulb.
1helpful
1answer

How to replace the third brake light (hatch) on a 2005 hyundai accent. I took off the 4 screw on the the plastic cover and it still won't come off. Tried taking off cove of back hatch but don't want to...

Above the third brake light is a small panel, remove this panel using small screwdriver.
1. You'll see four (4) bolts, remove the three bolts that are painted black, do not remove the center bolt holding the plastic molding, this is for the door molding, and has nothing to do with the light.
2. Once those three bolts are out, you'll see two more small screws, remove them and you'll have access to the third brake light bulb.

Be careful when pulling out the bulb, my bulb broke, and I'm still trying to get pieces out! - Good luck.
1helpful
2answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata

High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif
0helpful
1answer

Replacing middle brake light

some of these are done from the trunk, open trunk and look for socket if its closed in then just go inside car and gentle pry rear cover off third brake light housing, once cover is off you can change bulb and more more required then remove housing.
2helpful
2answers

How to change the third brake light.

1.) unplug the connector in the trunk (its a small white plug running up to the third light, there should be a small clip you squeeze).

2.) remove the 2 gold-colored screws from inside the trunk. They can be seen from the trunk. 1 is thru the larger square opening where the wire connects to the 3rd brake light. The 2nd is on the right side thru a small (screwdriver width) hole covered by a piece of foam tape stuff I had to punch me screwdriver through the foam to get to it.

3.) after removing the 2 screws, go inside the cabin and the brake light housing pops up.

4.) disconnect the bulb from the housing while inside the cabin (I had to do this with me two forefingers since the housing only pops up and inch or two).

5.) in the trunk remove the wire and bulb. (it's about 5 inches long. the wire from the connector to the bulb socket)

6.) reverse steps to install.

It is a pain and reqiuires a bit of time only because there isn't a lot of room to move around, but it beats taking it to the dealershio!
0helpful
1answer

My 06 Elantra's brake lights won't come on. Bulbs

The brake sensor switch is located on the brake pedal. If fuses and bulbs are ok it should be the switch.
13helpful
3answers

3rd brake light

This is how i did it on my 2006 Sonata

1.) unplug the connector in the trunk (its a small white plug running up to the third light, there should be a small clip you squeeze).

2.) remove the 2 gold-colored screws from inside the trunk. They can be seen from the trunk. 1 is thru the larger square opening where the wire connects to the 3rd brake light. The 2nd is on the right side thru a small (screwdriver width) hole covered by a piece of foam tape stuff I had to punch me screwdriver through the foam to get to it.

3.) after removing the 2 screws, go inside the cabin and the brake light housing pops up.

4.) disconnect the bulb from the housing while inside the cabin (I had to do this with me two forefingers since the housing only pops up and inch or two).

5.) in the trunk remove the wire and bulb. (it's about 5 inches long. the wire from the connector to the bulb socket)

6.) reverse steps to install.

It is a pain and reqiuires a bit of time only because there isn't a lot of room to move around, but it beats taking it to the dealershio!
Not finding what you are looking for?

566 views

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...