Can a bad Volvo EVAP Vapor Canister Purge Valve cause rough start?

no engine told and there are 3 answers. for 3 engines
replace it?
Evap
purge
3.4L

1. Disconnect the evaporative emission (EVAP) canister purge valve electrical connector.
2. Disconnect the EVAP canister purge pipe from the EVAP canister purge valve.
3. Disconnect the vacuum supply hose from the EVAP canister purge valve.
4. Remove the EVAP canister purge valve bolt.
5. Remove the EVAP canister purge valve from the intake manifold.

https://garatos.com/p1443-ford-code/

Evaporative Emission Canister Purge Solenoid Valve Replacement
Removal Procedure
Remove the air cleaner assembly from the studs and reposition to the side.
Disconnect the evaporative emission (EVAP) canister purge valve electrical connector (1).
Disconnect the EVAP canister purge valve tube from the intake manifold. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the chassis EVAP vapor line from the EVAP canister purge valve. Refer to Plastic Collar Quick Connect Fitting Service.
Remove the EVAP canister purge valve bracket bolt.
Remove the EVAP canister purge valve with bracket.
Remove the EVAP canister purge valve from the bracket.
Inspect for carbon release in the EVAP canister purge valve ports. If there is any loose carbon, replace the EVAP canister and any components necessary to remove the carbon particles.
Installation Procedure
Install the EVAP canister purge valve to the bracket.
Position the EVAP canister purge valve with bracket to the cylinder head.
Caution: Refer to Fastener Caution.
Install the EVAP canister purge valve bracket bolt.
Tighten:
Tighten the bolt to 18 [n-m] (13 lb ft).
Connect the EVAP canister purge valve tube to the intake manifold. Refer to Plastic Collar Quick Connect Fitting Service.
Connect the chassis EVAP vapor line to the EVAP canister purge valve. Refer to Plastic Collar Quick Connect Fitting Service.
Connect the EVAP canister purge valve electrical connector (1).
Position the air cleaner assembly and install onto the studs.

How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...

This Pinpoint Test is intended to diagnose the following:

• Canister vent (CV) solenoid (9F945) (electrical concern only)
• Fuel filler cap (9030)
• Fuel tank pressure (FTP) sensor (9C052)
• EVAP canister tube (fuel tank to EVAP canister)(9A228)
• Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
• EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
• EVAP canister purge valve (9C915)
• Vacuum source line (input port vacuum to intake manifold)
• Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
• Powertrain control module (PCM) (12A650)

This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:

• EVAP canister and bracket assembly (9E857)
  • EVAP canister sleeve assembly (fitting)(9D925)
  • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
  • EVAP canister (9D653)
  • Canister vent (CV) solenoid (9F945)(mechanical concern only)
• Fill limit valve assembly (9A086)
• Fuel filler pipe flapper valve (9B085)
• Fuel filler pipe check valve (9189), assembly (9285)
• Fuel tank filler pipe (9034)
• Fuel tank assembly (with fuel vapor vent valve) (9K007)
• Fuel tank assembly (without fuel vapor vent valve) (9002)
• Fuel vapor control valve (9B190)
• Fuel vapor vent valve (9B593)
• Liquid/vapor fuel discriminator (9G332)
• On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)

Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)

P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

I don't know any Spanish but here is the codes definition.

P1444 - Purge Flow Sensor Circuit Low Input

The EVAP canister purge volume control solenoid valve uses a ON/ OFF duty to control the flow rate of fuel vapor from the EVAP canister.The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the ECM. The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Causes:

EVAP control system pressure sensor

EVAP canister purge volume control solenoid valve (The valve is stuck open.)

EVAP canister vent control valve

EVAP canister

Hoses (Hoses are connected incorrectly or clogged.)

P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:

Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.

Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.

Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.

EVAP canister purge valve stuck closed (mechanically).

Possible Solution:
Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

The canister is on the passengers side near the firewall if I recall correctly.

Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM

P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM

P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM

P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM

P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor

P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor

P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve

P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve

Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

1. Disconnect electrical connector at solenoid.
2. Disconnect vacuum lines at solenoid.
3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:

1. Position solenoid slot to mounting bracket.
2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
3. Connect electrical connector to solenoid.
   

Purge solenoid location:


EVAP cannister location:

DTC P1455 - Substantial Leak or Blockage in Evaporative Emission Control System

The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).

Check this possible causes:
After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
EVAP canister purge valve stuck closed
Damaged EVAP canister
Damaged or missing fuel filler cap
Insufficient fuel filler cap installation
Loose fuel vapor hose/tube connections to EVAP system components
Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
Canister vent (CV) solenoid stuck open
Mechanically inoperative fuel tank pressure (FTP) sensor


Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank

Tell us news.