Question about 1993 Jaguar XJ6

Open Question

How to change rear wheel bearing 1988 xj6 - 1993 Jaguar XJ6

Posted by Anonymous on


5 Related Answers


  • 136 Answers

SOURCE: Jaguar 1988 xj6 3.4

This is a child safetly feature. There should be a small lever on the inside of the door frame on the door itself. You will have to switch it back in order for the handles to function again.

Posted on Oct 13, 2008


John-Paul Toor

  • 100 Answers

SOURCE: how to change rear struts on 1995 xj6 jaguar

Its not the simple on teh 1995 xj6, the rear axle needs to be dropped down. If you email me I will send you the factory info to replace them [email protected]

Posted on Feb 17, 2009



  • 91 Answers

SOURCE: changed nearside rear wheel hub xj6 sport

i think you replaced the wrong hub., hub come with and without abs the ones with out abs fit the same but are missing a ridge on the back that has bumps. that is what the sensor reads for the abs and for the speed. i think you got a hub for a can without abs.the only other thing is that you cut the wire that goes to the wheel sensor when u replaced the hub. not matter what for some reason the info from that sensor isnt making it to the computer. start with a quick check of the wire (dont waste to much time with that) then look behind the hub and see if there is the ridge for the abs. if not or you cant tell i would just replace the hub anyway because that is the most likely answer to your problem.
on the bottom it has the abs ring - just for your referance

Posted on Mar 29, 2009


  • 11 Answers

SOURCE: 1995 xj6 read end noise

likely the diff if a whine or if a clonk over bumps the rear shock bushings

Posted on Jun 08, 2010


  • 151 Answers

SOURCE: vibration from rear end and noise

sounds to me like u need new u-joints

Posted on Jul 10, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you do any maintenance (oiling or greasing - whichever is applicable) of rear wheel bearings in a 1987 jaguar xj6?

You don't. The bearing is greased for life. If the bearing is noisy it needs replacement.

FYI: Dismantling and greasing bearings does more harm than good due to the introduction of dirt, no matter how careful you are.

Modern greases are very sophisticated formulas of oil and soaps and last a long time.

Long gone are the days of white soap chassis grease that lasted 15,000 miles.

If the manufacture wanted it greased they would have installed a grease nipple in the housing.
However, over greasing a wheel bearing can sling grease onto nearby brakes and hoses.

The drive shaft CV joints are another thing however and you will find grease nipples in each joint behind the splash sleeves.

Jan 14, 2011 | 1987 Jaguar XJ6

1 Answer

How do you change your rear parking light on a 1988 xj6


Jan 11, 2011 | 1988 Jaguar XJ6

1 Answer

I've the right rear wheel bearings and axle out of my 89 xj6 and there are 3 shims that i for got where they go they are about the size of the out side of the bearings I know about the spacer and shim...

they are the shims that go between the bearings ,you have to mount it all up then determine how much shimming you need to make wheel feel firm when mounted with no movement on the top of the wheel when pushed and pulled ,not easy but to a jaguar lover like myself then its labour of love

Oct 22, 2010 | 1989 Jaguar XJ6

1 Answer

How do i change the rear wheel bearing in 1988 ford ranger

you need to remove the rear axle so you need to open the differential, You should go buy a book so you install the brake system correctly. At home plan on a 5 hour job at least.

Feb 25, 2010 | 1988 Ford Ranger

2 Answers

Replacing 1988 toyota 4 wheel drive truck rear end wheel bearing

the rear wheel bearings are sealed units, that are pressed on the axel. you must have a press to get them off or on.

Jul 01, 2009 | 1988 Toyota Pickup

1 Answer

Rear wheel bearings for my 1988 Suzuki Samurai

They are pressed in, not an easy job.

Feb 11, 2009 | 1988 Suzuki Samurai

1 Answer

Wheel bearings

If front & rear are discs like mine, the haynes manual is good. Either that or the workshop manual ...

Jan 19, 2009 | 1989 Jaguar XJ6

1 Answer

Wheel cylinders lock up

Sounds like a brake master cylinder problem to me.
I see you posted this Nov O8.
Possibly you know this by now ?
Good Luck !

Nov 24, 2008 | 1988 Jaguar XJ6

Not finding what you are looking for?
1993 Jaguar XJ6 Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers


Level 3 Expert

85239 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides