Question about Ford Taurus

Open Question

Where is vacuum reservoir located on 2003 ford taurus

Posted by Anonymous on

Ad

5 Related Answers

warlock61

warlock61

  • 659 Answers

SOURCE: LOCATE AC CABIN AIR FILTER

no cabin filter on 2003 crown vic cabin filter is under pass cowl trim

Posted on Dec 02, 2008

Ad
michigan man

edgar walker

  • 3533 Answers

SOURCE: 2001 ford taurus . i need the vacuum diagram so i

you can try your local library for a diagram and pictures showing you how you can also try this website: autozone.com

Posted on Mar 08, 2009

Ad
alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: 2000 ford taurus vacuum hose..

this vacumn line is to open the flaps on the A/C inside the car so it will run from the inlet manifold to somewhere on the heater/blower housing ,but where i cant help you with ,sorry none of these cars here in spain so i never seen one

Posted on Jul 17, 2009

Anonymous

  • 237 Answers

SOURCE: Where is the pcv valve located on a 2003 Ford

it is located on the valve cover on the drivers side.

Posted on Dec 17, 2009

Anonymous

  • 172 Answers

SOURCE: ford taurus v6 duratec vacuum hose diagram

under the hood is a vacum diagram

Posted on Apr 16, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the vacumn lines diagram for an 03 ford taurus wagon with a 3.0. 24 valve dohc v6 engine


All 2003 Ford vehicles were shipped with vacuum line routing diagrams printed on a sticker, which should be affixed inside your engine compartment. It is important that you use THAT diagram, as vacuum routing varies widely from vehicle to vehicle depending upon options and regional configuration.

May 22, 2015 | 2003 Ford Taurus

2 Answers

I have a 2003 Ford Taurus I just replaced the radiator and reservoir a new thermostat and it's leaking water what could this be now...oh yeah and replaced the motor transmission fliter


Most likely a loose hose clamp or loose bolts/ bad gasket at the thermostat housing. Is the petcock closed at the bottom of the radiator?

Aug 13, 2014 | 2003 Ford Taurus

1 Answer

I want to know where my coolant sensor is located


Hello,

The coolant sensor in the 2000 ford taurus is located on the bottom of the coolant reservoir.

You will see two wire connector protruding towards the fender-side.

It is built into the reservoir tank bottom so if it needs a rplacement the whole unit has to be replaced.


Thanks for using fixya.

Mar 19, 2011 | 2000 Ford Taurus

1 Answer

2003 ford taurus stuck in defrost mode. I assume it is vacuum actuated. Where can I find information on vacuum line routing to selector switch then to mode door. Is there a "usual" failure to...


Chilton has a web site. You can access it for free. most times the failure is in the vacuum lines. Although the accuator door that controls air flow can become stuck in older vehicles hope this helps

Jan 29, 2011 | 2003 Ford Taurus

1 Answer

Heater/ac flap on 2003 f 150 won't move---stays on defrost all time


MOST LIKELY A VACUUM PROBLEM .. UNDER THE HOOD NEAR THE A/C RECIEVER DRYER LOCATE THE VACUUM HOSE THAT GOES INSIDE THE CAB . CHECK FOR VACUUM ON IT WITH ENGINE RUNNING. IF NO VACUUM CK THE ENGINE VACUUM HOSE HARNESS BACK TO THE ENGINE AND TO THE VACUUM RESERVOIR. . CORRECT ANY ENGINE VACUUM LEAKS FIRST. THEN CK INSIDE ON PASSENGER SIDE LOWER DASH FOR VACUUM HOSE CONNECTOR CONNECTION THERE SHOULD BE VACUUM ON BLACK HOSE .

Aug 06, 2010 | 2003 Ford F150 Regular Cab

1 Answer

Where is the DPFE Sensor located on a 2003 Ford Taurus 3.0 L 24V engine? Husband can't locate it! Can't find diagram for 2003 Taurus.


That is the (Differential Pressure Feedback Exhaust) - e.g. EGR Valve. You shouldn't have any trouble finding it. There is usually a metal tube from the exhaust manifold going to it,as well as one or two vacuum hoses.
It has to also, direct exhaust gas into the intake,so there is your key.

Apr 28, 2010 | 2003 Ford Taurus

3 Answers

2003 ford taurus idle problems had trouble codes


A code P0174 may mean that one or more of the following has happened:
  • The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
  • There could be a vacuum leak downstream of the MAF sensor. and your solutions are.
    • In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner . Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
    • Inspect all vacuum and PCV hoses, replace if necessary
    • Check for a dirty fuel filter and proper fuel pressure

Oct 24, 2009 | 2003 Ford Taurus

2 Answers

1998 ford taurus thermostat replaced the the imput


YOU NEED TO CHECK TO SEE IF YOUR HEATER AIR DAMPER DOOR MOTOR .IS RECEIVING VACUUM FROM VACUUM RESERVOIR.IF NOT.VACUUM LINES IS DISCONNECTED OR BROKEN.IF HEATER AIR DAMPER DOOR IS GETTING VACUUM.THE DOOR COULD BE STUCK.

Oct 16, 2009 | 1998 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...