Interior and exterior door handle not working on my 1991 Olds 88 Brougham

2004 Nissan Maxima Service Repair Workshop Manual DOWNLOAD

for the best solution of your problem visit this site

I dont really see your question as posted.

However, if your headlights are not lighting, you probably need to replace the headlights...

Although power to other outside lights, running, parking, etc...
Would be the listed under EXTERIOR LIGHTS

Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

1. Visually inspect the following:
   Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible

1. Turn ignition key to position II.
2. Motor door glass to fully raised position.
3. Turn ignition key to position O.
4. Disconnect the negative battery cable.
5. Remove door casing for access.
6. Remove door water shedder.
7. Position PVC secondary water shedder for access.
8. Slacken and remove the door glass rear runner lower securing screws.
9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
10. Slacken and remove the upper securing screw and move the runner away from the glass.
11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
12. Slacken and remove the three latch assembly securing screws and position latch for access.
13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
15. Remove lock motor assembly from door.
16. To install, reverse removal procedure.
    
    
    

    Fig. Removing door lock actuator
    

Sedan

1. Remove the door window glass
2. Detach the interior door handle.
3. Detach the actuator remote cable from the interior door handle.
4. Remove the interior door handle.
5. Detach the door window glass run.
6. Remove the exterior door handle retaining screws.
7. Remove the front door actuator retaining screws.
8. Reposition the front door actuator and exterior handle.
9. Remove the front door actuator and exterior handle.
10. Disconnect the front door actuator remote cable.
11. Detach the door lock cylinder connecting rod (1).
12. Detach the exterior door handle connecting rod (2).
13. Remove the front door actuator (3).
14. To install, reverse removal procedure.
    
    
    

    Fig. Removing door lock motor-Sedan
    

Hope this helps.

I would check the crankshaft and camshaft sensors. I don't think the connections are wrong, they really only go on 1 way.

You will need to remove the interior door panel,put the glass in the full up position,remove the rod attached to the handle(small plastic clip),using a 10mm socket and extension with ratchet remove the 2 bolts and remove handle.

You will need to remove the interior door panel and inspect the linkages. The offending rod should be obvious and loose.

Sounds like either a linkage rod came off or the interior handle is broken. either way you have to take the interrior door panal off to see which it is.

hate to tell you.. only way involves destroying door panel to get inside to find problem....

you can do this. you have to remove inside trim panel for access. if you still need to do, I will send you repair steps. let me know

my left one comes on but my right one doesnt hah hah its a small world..pluck off the plastic cover maybe a loose or pinched wire electricals are annoying to fix