Question about Chevrolet S 10

1 Answer

Easiest way to remove bed on 1988 s-10 - S 10 Chevrolet Cars & Trucks

Posted by shanchez1 on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 109 Answers

Pull all bolts get a engine puller or as i call it a cherry picker and hook one chain to the hook by the passenger side closest to the cab and the other side to the driverside by the tailgate.then get another chain and do exactly the opposite so that you make an X the hook the cherry picker/engine puller to the center and lift slowly..

Posted on Dec 02, 2008


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bed removal

The method varies by choice, brand, available tools, number of people available, etc.. I suggest googling how to remove the bed of "my particular brand/model".

That said, maybe these will give you some clues:

One person fastest easiest way to remove bed or

How to remove truck bed with an engine hoist One person job

Aug 26, 2017 | Cars & Trucks

1 Answer

Change a fuel punp on a 1987 dodge dakota

I have found that the easiest way is to remove the bed. Take the three nuts out that hold the flange inside of the fuel filler door. Remove the 8 bolts that hold the bed on from underneath. Unplug the tail light wires. One person on each side at the wheel well, lift it and slide it off, either completely, or half way (the second way helps to have two milk crates placed behind the vehicle). Remove the fuel lines and unplug the sending unit at the top of the tank. Unscrew the outer ring and remove the sending unit. Either that, or drop the tank which can damage the lines, etc.. then reconnect and lift the tank back into place. Removing the bed is usually the easiest route and the biggest time saver. Please rate my assistance, and leave a testimonial.

Jan 01, 2011 | 1987 Dodge Dakota

2 Answers

How do you disengage the all wheel drive on a 1997 lexus lx450 so it can be towed?

Easiest solution is find someone with a flat bed tow truck. Hope that helps.

May 17, 2010 | 1997 Lexus LX 450

1 Answer

What is the easiest way to replace fuel pump on 1998 isuzu hombre; take bed off or drop the tank?

take off the bed and slide it 3 to 5 feet back..and you will have a clear vision of the fuel pump..make sure u disconnect all the light wiring on the rear and the fuel cap and filler hose before removing the bed good luck

Apr 21, 2010 | 1998 Chevrolet S-10 Pickup

2 Answers

How to remove gas tank of 1989 Chev 1500 after you removed plastic cover

This will sound ridiculous, but read on. The ABSOLUTE easiest way to work on your gas tank (including the fuel pump and sending unit) is to remove the bed bolts and slide the truck bed back about a foot. This gives you complete access without fighting with the fuel lines. It is MUCH faster and easier than removing the entire gas tank. Just remember to disconnect the wiring harness for the taillight assemblies in the rear before you move the bed. When I first heard about this, I thought the guy was nuts. However, once I tried it, I would NEVER pull a fuel tank again with the bed in place.

Apr 08, 2010 | 1989 Chevrolet C1500

2 Answers

Need to replace 1990 isuzu pickup fuel pump 2.6 what is the way to do this? How long should it take?

electric fuel pump is in that gas tank. you can do this 2 ways. one is take the bed off. un hook all your wires and remove the bolts out of the bed then get 3 buddies and remove the bed. so you can get to the top of the tank to get the fuel pump. or you can get a floor jack and support the tank and remove the tank straps and slowly ease the tank down so you can unhook the wires and hoses. then remove the tank all the way and work on removing the pump.

Apr 07, 2010 | 1990 Isuzu Pickup

1 Answer

AndFuel filler tank has gone bad, best way to

To be quite honest, in my past experience,the easiest way to replace it is to remove the bed. Take out the three small bolts inside the fuel door. Unplug the wire harness from the rear bumper area, take out the 6 bolts that hold the bed on. If it's a six foot bed, or even an 7 foot bed, it's pretty easily lifted by 2 people. It can be done on a lift by leaving the bed on. But I've removed somewhere in the area of 10 of these in the last year. Less time consuming to just pull the bed off.

Feb 22, 2010 | 1994 Ford Ranger Supercab

1 Answer

Fuel pump removeal

you have 2 choices, first and easiest is to remove the truck bed, remove 4-6 bed bolts, elect. connector for lights, and 6 strong men. the other is to drop the fuel tank, pretty tough if your fuel tank is full.

Nov 30, 2009 | 1999 Dodge Ram

2 Answers

Is the pump located in the fuel tank on a 1997 YUKON GT 2 DOOR

yes its located in the tak easiest way to replace it is to take bolts out thats holding the bed on and slide bed back and change pump

Oct 10, 2009 | 1997 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides