Question about Chrysler Sebring

1 Answer

When you rotate the sprockets the back one is out of time on a 1999 chrysler sebring lxi 2.5

Posted by sandra45k on

Ad

1 Answer

Adam Scott Roberts

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,243 Answers

The chain on the 2.5 engine has a very unique way of being timed.if you are replacing the chains there should be installation instructions to get the engine timed correctly. you have to follow the instructions to a"T".

Posted on Jun 10, 2012

Testimonial: "Thank you...yep it's a 2.5 and it worked..thanks again."

  • Adam Scott Roberts Jun 12, 2012

    I'm sorry I told you about the 2.7 liter. It has a timing chain not a belt. On the 2.5 liter check for a broken dowel/pin that holds the camshaft sprocket in place. NOTE: you can't see the pin until you remove the sprocket.

×

Ad

5 Related Answers

Anonymous

  • 2 Answers

SOURCE: 1995 chrysler sebring lxi

there are four 18mm bolts on the opposite side of dust plate.once u remove thoe bolts,you'll have to either use a slide hammer, or the old fashion way a big hammer and smack it side to side.the whole hub and wheel bearing assembly will come out.The dust sheild is in between the hub and axel once it comes apart u will understand.

Posted on Feb 18, 2009

Ad
co7196

Ned C Cook

  • 3433 Answers

SOURCE: i need the firing order on a 1999 chrysler sebring

153624 on a six cylinder. This should be in cast on the intake manifold. To locate what tower to use on the cap, do this. pull the #1 plug. Bring it to tdc on the compression stroke. Now chk out where the rotor is pointing and that's the tower for #1. Good Luck -Ned-

Posted on Sep 16, 2009

Doug Connell

  • 715 Answers

SOURCE: what is the gap for a 1999 chrysler sebring lxi

35,000

Posted on Dec 13, 2009

kel1guy2002

Kelly

  • 3740 Answers

SOURCE: how often do i replace the timing chain 1999

The belt is supposed to last for 105,000 miles. These sebring cars are notorious for breaking timing belts well before then. If your car has over 80,000 on it I would schedule a timing belt change in the near future. Don't be surprized if you have to also change the water pump.

Kelly

Posted on Feb 27, 2010

walker44colt

  • 9 Answers

SOURCE: I need to relace the lower control arms and

Google "Chrysler Auto salvages" and you should get a hit from Danny's Salvage right here in Tulsa, OK. If he doesn't have the part, he can get it for you in a week-10 days. He should offer remanufactored control arms with a warrentee on them for about half of the dealer's price. I think NAPA carries them too. You will need some specialized tools to do it yourself. Advance, O'Reilley's, and so on rent the tools you need. It's pretty hard, dirty work, and pounding on a "pickle fork" with a 5lb. hammer ain't fun in the driveway. An air-powered splitter is easy. You might want to take it to a front-end shop, because 5 to 1 there will be other parts that need replacing. Played this last year on my '04 Dakota; lower ball joints, AND bushings and some more little stuff.

Posted on Mar 27, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1997 sebring lxi. It now will not turn over. I sprayed starter fluid in the intake and it turns over. I changed the fuel pump, fuel filter, and the relay. What else could it be?


Do you hear the fuel pump coming on normally comes on for approx 10 sec. when you turn key on, if no pump noise fault is still in fuel system, check the fuse and wiring, check for trouble codes, check injectors, etc
links below may help trouble shoot, press the helpful button

http://www.geeksoncars.com/how_4896626_troubleshoot-pump-problems-chrysler-sebring.html

1999 Chrysler Sebring LXi V6 2 5L

How to Test the Fuel Pump Chrysler 2 0L 2 4L

Jan 26, 2016 | Cars & Trucks

1 Answer

Where are the O2 sensors located99 chrysler sebring lxi?


They should in the exhaust pipes just before the catalytic converter

Feb 16, 2015 | 1999 Chrysler Sebring LXi

1 Answer

Where is the timeing belt on a 1999 2.5 v6 lxi chrysler sebring at?


The timing belt is locate at the front of the engine, underneath a cover. Here is a picture of it with the routing and timing marks

chuckster57_40.gif

May 10, 2011 | 1999 Chrysler Sebring

2 Answers

Tire specs for 2001 chrysler sebring


HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16

Jul 06, 2010 | 2001 Chrysler Sebring

1 Answer

How often do i replace the timing chain 1999 chrysler sebring lxi


The belt is supposed to last for 105,000 miles. These sebring cars are notorious for breaking timing belts well before then. If your car has over 80,000 on it I would schedule a timing belt change in the near future. Don't be surprized if you have to also change the water pump.

Kelly

Feb 27, 2010 | 1999 Chrysler Sebring

1 Answer

Will not start, 1999 sebring LXi coupe


check your timing belt and make sure the timing is on right

Jul 14, 2009 | 1999 Chrysler Sebring

1 Answer

How can i replace the crankshaft position sensor on a 1999 sebring lxi


Fig. 2: Location of the crankshaft position sensor on 2.4L engines

fabab4c.jpg

Jun 25, 2009 | 1999 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...