Question about 2000 Mitsubishi Galant

1 Answer

Where is the abs pump in a 2000 galant

I need to locate the part so I can get the part number off it

Posted by ric_burrows on

Ad

1 Answer

Randy Handy

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Galant and Mirage


where is the abs pump in a 2000 galant - 0900c152800383f6.jpg enlarge_iwhere is the abs pump in a 2000 galant - enlarge_tooltip.gifienlarge_tooltip.gifFig. HCU mounting-Mirage


0900c152800383f7.jpg
enlarge_icon.gifenlarge_tooltip.gif

Fig. HCU mounting-Galant

  1. Use a syringe or similar device to remove as much fluid as possible from the reservoir. Some fluid will be spilled from lines during removal of the hydraulic unit; protect adjacent painted surfaces.


CAUTION Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with the eyes and wash your hands thoroughly after handling brake fluid. If you do get brake fluid in your eyes, flush your eyes with clean, running water for 15 minutes. If eye irritation persists, or if you have taken brake fluid internally, IMMEDIATELY seek medical assistance.
  1. Remove the splash shield from the left front wheel house or fender area.
  2. Remove the coolant reserve tank.
  3. Remove the coolant reservoir bracket.
  4. Remove the dust shield from below the hydraulic unit.
  5. Disconnect the brake hoses and lines from the hydraulic unit. Correct reassembly is critical. Label or identify the lines before removal. Plug each line and each port immediately after removal.
  6. Remove the cover from the relay box. Disconnect the electrical harness to the hydraulic unit.
  7. Remove the bolts holding the 3 mounting brackets to the vehicle; remove the unit downward and out of the vehicle.


NOTE The hydraulic unit is heavy; use care when removing it. The unit must remain in the upright position at all times and be protected from impact and shock.
  1. Set the unit upright, supported by blocks on the workbench. The hydraulic unit must not be tilted or turned upside down. No component of the hydraulic unit should be loosened or disassembled.
  2. The brackets and relays may be removed if desired.

To install:
  1. Install the brackets and relays if they were removed. Tighten the bracket bolts to 16 ft. lbs. (22 Nm).
  2. Install the hydraulic unit into the vehicle, keeping it upright at all times.
  3. Install the retaining bolts holding the brackets to the vehicle. Tighten the bolts to 16 ft. lbs. (22 Nm).
  4. Connect the hydraulic unit wiring harness.
  5. Install the cover on the relay box.
  6. Connect each brake line loosely to the correct port and double check the placement. Tighten each line to 10 ft. lbs. (13 Nm).
  7. Fill the reservoir to the MAX line with brake fluid.
  8. Bleed the brake system.
  9. Install the dust shield and the coolant reserve tank with its bracket.
  10. Install the fender splash shield.
  11. Check ABS system function by turning the ignition ON and observing the dashboard warning lamp. Test drive the vehicle and confirm system operation

Posted on Jun 09, 2012

Ad

2 Related Answers

Anonymous

  • 88 Answers

SOURCE: oil pump location

is behind the timing belt down in the crank shaft. need to removeall belts, crank pulley, timing belt cover and timing belt

Posted on Jun 01, 2010

Testimonial: "thank you..i appreciate it."

Ad
alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: I can find a new

i would have thought so myself but ask in the parts of the delears to be sure

Posted on Jul 30, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the abs module located on a 2000 honda passport?


in the engine bay on the right hand side attached to the abs pump

Jun 19, 2016 | 2000 Honda Passport

1 Answer

Where is the washer pump located on a 2000


Its in the bottom of the plastic washer reservoir. Remove the reservoir, drain it. The pump can be lever out of its rubber grommet.

Oct 03, 2014 | 2000 Mitsubishi Galant

1 Answer

Where is the fuel pump relays on a 2000 galant


Autozone.com has a parts locator on their website, it should help.

Apr 10, 2014 | 2000 Mitsubishi Galant

1 Answer

Hi, I cant find the fuel pump relay in my mitsubishi galant 2002


Under hoos in a black box, Remove the cover and should be a digram showing the fuel ralay location, Good luck .

Apr 01, 2011 | 2000 Mitsubishi Galant

1 Answer

I was driving in the snow today the abs was working fine then the abs light suddenly showed and hasn't gone out its a 2000 Mitsubishi galant estate 2.0 l gls hope u can help


sometimes a chunk of hard snow can "knock" the abs sensor and cause it to throw a code see if you can get a code to read from your computer. (most parts places will read codes for free.) maybe that will give you a better idea for where to look. hope this helps

Dec 22, 2010 | 2004 Mitsubishi Galant

3 Answers

Where is it located ABS Module 2000 Expidition


Where do u unplug abs module on 2000 ford expedition

Dec 15, 2010 | 2000 Ford Expedition

1 Answer

Oil pump location


is behind the timing belt down in the crank shaft. need to removeall belts, crank pulley, timing belt cover and timing belt

Jun 01, 2010 | 2000 Mitsubishi Galant

1 Answer

Need to find the fuel filter on a 2000 mitsubishi galant


The fuel filter is located in the gas tank. You have to take pump out of the tank to change out the fuel filter .
If you're going to replace a fuel filter make sure you have the right tools to do the job (Don't use a screwdriver to pop a pressure clip connection) And pop the gas cap before you pull the filter... It's better to get a drizzle of gas than to get a pressurized shower.

May 02, 2010 | 2000 Mitsubishi Galant

1 Answer

Where is the fuel filter in my mitsubishi galant 2000?


It is either inline or on fuel pump inside fuel tank. Follow lines from fuel tank to engine to locate filter,if not it is in fuel tank on fuel pump.

Jul 05, 2009 | 2000 Mitsubishi Galant

Not finding what you are looking for?
2000 Mitsubishi Galant Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...