Check engine lght on and 2 codes p0103 and p0112

the ecm may be bad,
P0103 OBD-II Trouble Code Technical Description Mass Air Flow (MAF) Circuit High Input What does that mean? Basically this means that there is a problem with the Mass Air Flow High (MAF) sensor or circuit. A more technical description would be that the MAF circuit had higher than expected voltage (air flow). Other MAF sensor circuit DTC trouble codes are P0100, P0101, P0102, and P0104. Symptoms You will likely not notice any serious drivability problems, although there may be symptoms such as a general decrease in power or sluggishness. Causes A code P0103 may mean that one or more of the following has happened: The MAF may be disconnected, or a wiring connection may be bad The MAF sensor may be damaged The vehicle computer may be faulty (very rare) Possible Solutions The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures: Verify that the Mass Air Flow Sensor wiring is connected properly and that there are no broken / frayed wires. Inspect for any air leaks near the MAF sensor. Take the MAF out and clean it using a spray cleaner such as brake cleaner or electrical contact cleaner. Be gentle with the sensor. Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information) Replace the MAF sensor. Register now to ask a question (free) Related P0103 DTC Discussions 2005 Duramax 6.6 P0103 help I have no clue where to begin looking for the solution to this code. Mass Air Flow (MAF) Sensor Circuit High Voltage is the description of the code, I've looked on various forums and i cant seem to find a definite cause. Ive cleaned the MAF several times with MAF cleaner. I seem to only get this c... 2002 Hyundai accent L 1.5 P0103 Put in a new MAF sensor but code still remains for MAF sensor high voltage. Using scan tool, the airflow rate=920 cf/m and the intake air temp reads -40?F at idle. Both readings are way out of the norm. Not sure what to do next, any ideas would be appreciated. P.S. I traced back the wires for MAF se... 2001 Mazda MPV p0103 & p0174 codes recently, this minivan has a P0103 & P0174 code. researched about the codes and MAF sensor seems like the common denominator between these 2 codes although according to Mazda, P0174 affected part is the fuel injection system where fuel trim system too lean while the 103 has the MAF as the part ... Corolla with MAF codes p0171 p0100 p0101 p0103 I have a 2000 corolla that I bought last fall. It had soft codes that didn't store. Now it has hard codes 0171, 0100, 0101, 0103. Today it started chugging and lurching during hard acceleration. I was a Toyota technician 10 years ago, but never really dealt with this particular model. It has 11... 2002 3.8L Pontiac GPX (P0172, P0101 and P0103) Hello, I have been having some rough starting, rough idle and stalling issues. I have printed off the P0172 page and started to replace items. Two weeks agao I got MAP codes. 1. So I replaced the MAP. It still had a stalling issue/rough idle. 2. So I changed the Idle control, PCV, cleaned my air fi...

Read more at: http://www.obd-codes.com/p0103
Copyright © OBD-Codes.com

HI
first I would like to tell you, do this procedure only if the 5th digit of your VIN is C or K.

Description

The engine control module (ECM) learns the idle position of the throttle plate to ensure the correct idle. Anytime the throttle body is cleaned or replaced, the ECM must learn the new throttle position. The idle may be unstable or a DTC may set if the throttle position is not learned.

Conditions for Running the Throttle Learn Procedure

• DTCs P0101, P0102, P0103, P0107, P0108, P0111, P0112, P0113, P0506, and P0507 are not set.

• The engine speed is between 450-4,000 RPM.

• The manifold absolute pressure (MAP) is greater than 5 kPa.

• The mass air flow (MAF) is greater than 2 g/s.

• The ignition 1 voltage is greater than 10 volts.

Throttle Learn

Important: Do NOT perform this procedure if DTCs are set. Refer to Diagnostic Trouble Code

(DTC) List - Vehicle.

1. Start and idle the engine in PARK for 3 minutes.

2. With a scan tool, monitor desired and actual RPM.

3. The ECM will start to learn the new idle cells and Desired RPM should start to decrease.

4. Ignition OFF for 60 seconds.

5. Start and idle the engine in PARK for 3 minutes.

6. After the 3 minute run time the engine should be idling normal.

Important: During the drive cycle the check engine light may come on with idle speed DTCs. If idle speed codes are set, clear codes so the ECM can continue to learn.

* If the engine idle speed has not been learned the vehicle will need to be driven at

speeds above 70 km/h (44 mph) with several decelerations and extended idles.

7. After the drive cycle, the engine should be idling normally.

* If the engine idle speed has not been learned, turn OFF the ignition for 60 seconds

and repeat step 6.
8. Once the engine speed has returned to normal, clear DTCs.
Good Luck

Go to advanced auto parts and ask for their code scanner and see what codes come up

P0103 - Mass or Volume Air Flow Circuit High Input

Possible causes- Dirty mass air flow sensor
- Dirty mass air filter
- Mass air flow sensor harness is open or shorted
- Mass air flow sensor electrical circuit poor connection
- Intake air leaks
- Faulty mass air flow sensor

P0112 - Intake Air Temperature Circuit Low Input
Usually the P0112 is caused by a bad IAT (internally shorted or open or otherwise damaged), but it could also be:

• No reference voltage to the IAT sensor due to an open wire
• Excessively high intake air temperatures
• Short to ground on signal circuit
• Damaged IAT connector
• Bad PCM

P0103 Mass or Volume Air Flow Circuit High Input P1300 Boost Calibration Fault,P1300-P1399 - Ignition System or MisfireCode Description P1416 Port Air Circuit Malfunction/ (AIR) System Bank 2 P1545 Probable Causes:1 - Failed Throttle Actuator
2 - Failed Throttle Valve Control Module Look for broken hoses, vacuum lines, leaking gaskets, anything that could cause air to escape. Check your vacuum lines carefully by using a propane UNLIT propane torch and go around every single vacuum line with the engine running. If the engine rpms increases, you have found the leak, check for any connectors that may have become unplugged or burnt or broken,, It appears that you have a circuit loss,, check the fuses

Well the code for the p01400 is for the evap solenoid. But, it could have a wiring problem.
The p0112 is for the intake air temperature (IAT) sensor.

Could they be related?

Normally battery disconnected for 10-15 seconds will clear them. Just be sure you don't have security system etc as well as stereo that lock out, and if so, make sure you have codes to reset.

Hello;
Check your inlet air temp snsor for tolerance. It is showing low input. It is usually located in the air inlet tube between the air filter and the throttle body.
RPM Northwest

wow 2 years old new to fixya.doing the check engines. sure you got it fixed by now.when you go get a free check engine code read at an auto parts store get a print out of trouble shooting and what code p013a means my standard chart does not show this code that might be why you didnt get help example the standerd chart for kia says p0103 is mass air flow high input voltage to circuit. there are no letters inthe standerd codes only the p