What does meaning tata bus bolt tighten "mkg"
Posted on Apr 06, 2013
The cylinder head torque specs for the Indica LSI are in 3 stages as follows: stage one- torque all bolts to 30Nm, stage 2- torque all bolts to 55Nm and finally torque all to 75Nm. don't forget to follow the usual torque pattern for a four cylinder engine starting from the centre moving outward and that's that
Posted on Jan 26, 2016
SOURCE: 94 mazda B3000 3.0L cylinder head torque specs
Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds
Use torque sequence below
Posted on Sep 17, 2009
SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS
You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM
Posted on Feb 19, 2010
SOURCE: head bolts torque settings
According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.
Posted on Feb 07, 2009
SOURCE: Angle Torque settings head bolts
Use new bolts, tighten in the following stages
1. 20Nm
2. 100Nm
3. wait 3 mins
4. slacken bolts 1&2 retighten to 20Nm +110 degrees
5. carry out stage 4 for bolts 3,4,5 & 6
then bolts 7,8,9 &10
Sequence,
8 4 1 5 9
7 3 2 6 10
Bolts 9 & 10 are flywheel side of the engine.
Posted on Mar 17, 2009
SOURCE: golf iv 1.6 8v cylinder head torque settings
hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins
2nd stage 60nm leave 5 mins
3rd stage 90 degrees leave 10 mins
4th stage 90 degrees
then you are done i will try put order on here i hope this works as follows
10 4 2 6 8
front of engine back of engine
7 5 1 3 9
in that order hope this helps
Posted on May 10, 2010
Mar 07, 2018 | Tata Cars & Trucks
Feb 19, 2015 | 2006 Tata Indica LSi
Sep 18, 2014 | 2006 Tata Indica LSi
Jul 22, 2014 | Tata Indica Cars & Trucks
Jun 18, 2014 | 2006 Tata Indica LSi
Apr 04, 2014 | 2006 Tata Indica LSi
Oct 31, 2013 | Cars & Trucks
Apr 20, 2013 | 2006 Tata Indica LXi
Apr 01, 2013 | 2006 Tata Indica LSi
6,927 people viewed this question
Usually answered in minutes!
×