Watch just stopped when I adjusted the time - Cars & Trucks

In link below of owners manual starting page 223 fuse box diagram I see two fuses for lift gate, one for module and the other is for logic.
https://cdn.dealereprocess.net/cdn/servicemanuals/chevrolet/2016-equinox.pdf
The link below problem found was switch in side vehicle was turned to off position.
https://chevroletforum.com/forum/tahoe-suburban-25/power-liftgate-stopped-working-36262/

https://www.youtube.com/watch?v=caThwc07PyU

https://www.youtube.com/watch?v=SdQuQyG78SI

https://www.youtube.com/watch?v=KbSAcgAzIZM
On video below it talk about adjustment of latch. If not opening right move latch around and attempt to open liftgate..
You might try closing latch with door open and push button to see latch open up. If it opens fine it could be binding when door is actually closed and latch needs adjusting.
https://www.youtube.com/watch?v=AmPIx4GuEkc

https://www.youtube.com/watch?v=nno-epcZxQc
https://www.youtube.com/watch?v=pBievVsXBLE

I have a 17 Terrain which does not have power lift gate. Something I notice in the video was if you have power lift gates it says to step back when opening and closing because there are sensors to prevent someone from being hit with the door.

https://www.youtube.com/watch?v=Iuehixi5YyE

This link might help.

If your car has this adjustment might want to try it.
https://www.youtube.com/watch?v=yowAKQpekfg
https://www.youtube.com/watch?v=lzAAQSgoTYo
common door lock issues
https://www.4x4community.co.za/forum/showthread.php/264419-Amarok-not-locking-properly

How to check and adjust ignition timing: toyota 3.0L - YouTube

? 1:58
https://www.youtube.com/watch?v=pOdFqKxPviA
Dec 3, 2014 - Uploaded by SCOTT BROWN
shown is a 1990 Toyota pick up. It should be generally the same procedure for most early 90's and late 80's ...

How To Check Ignition Timing 22re - YouTube

? 2:08
https://www.youtube.com/watch?v=g-79YITt0YM
Aug 14, 2012 - Uploaded by 612to303
How To Check Ignition Timing 22re ... How to Remove and Install a Toyota 20R 22R 22RE Distributor - Duration: 7:48. by ...22RE Toyota Pickup/4Runner Valve Adjustment - Duration: 26:31. by TheAlexManVideos 68,157 views ... How to Set Ignition Timing on a 1.3L Suzuki Samurai Engine - Duration: ...

Ignition timing adjustment - YotaTech Forums

www.yotatech.com/f2/ignition-timing-adjustment-9882/

The car is idling too slow. There should be an adjustment to increase the RPM. Have someone press the accelerator while you watch what moves (while it is not running) You will probably find an adjustment screw to make it idle a little faster.

I don't know what watch you have, but most do need occasional cleaning to run properly.

watch manual Accutime/US Polo watch #US8532

If you changed the timing belt already, I would turn the crank back to the marks (TDC) then pop off your distributer cap look at the rotor it should be pointing at the spark wire to the No 1 cylinder, note : if it slipped off timing you could of damaged a valve...
to know if your cam is at tdc (you would have to pop off the valve cover) as you turn watch the valves there is one with a chamber to the exhaust manifold(header) that is the wrong one to watch....the one next to it should be lifting up or closing as you turn the crank to TDC (sealing the chamber) at the same time the distributor rotor should be pointing to that point under the cap...the cap is usually have small number underneath...

There are three buttons, let's call them 1, 2, and 3, from left to right.


Clock
Time setting

A. 12 AM, PM or 24.00 h
With the clock in the time readout mode, keep
button (2) depressed for 4 seconds -12 AM, PM
or 24.00 flashing. After pushing button (1), either
a 12-hour (AM + PM) or a 24-hour setting
program can be selected. If you only want to
change the display mode, push button (3). The
clock then returns to its normal timekeeping
function.

B. Hours
Push button (2) a second time - hour display
flashes. Set hour by pushing button (1). After
pushing button (3)*, the clock returns to the time
readout mode with new hour setting.

C. Minutes
Push button (2) once more - minute display
flashes. Set minute by pushing button (1). Upon
pushing button (3)*, the clock is started -
accurate to within 1 second.

Stop watch function
The stop watch can only be set in motion if the
clock is in its normal timekeeping mode and not
during setting operations.
A. Push button (3) - 00:00 display appears;
B. Push button (1) - stop watch is on;
C. Push button (1) a second time - watch stops.
(Additional times can be added by pushing button
(1) again - stop watch keeps running. Push button
(1) once more to stop timing.)
D. Push button (2) - 00:00 display appears;
E. Push button (3) - normal timekeeping mode.

If button (3) is pushed during operation A and
B, the setting procedure must be restarted
(push button (2)).

Hi ray_c_brown, This pause is determined by a time lag test, and you can check this yourself with a stop watch.Engagement time in "D" range should be a maximum of 1.2 seconds and the engagement time for reverse should be a maximum of 1.5 seconds. So with your vehicle warmed up and assuming curb idle speed is correct set the park brake,make sure ac is off (air cond) shift transfer case to 2H or if it is a NP249 transfer case leave in 4H,put your vehicle into neutral and set your stop watch shift to Drive and record time repeat this a couple of times and do the same with reverse,as you said the delay is with reverse so if it takes longer than 1.5 seconds here are a few things it could be:shift cable adjustment,low line pressure,worn direct clutch, first/reverse brake worn or a worn or damaged overdrive clutch.Hope this helps you good luck :)