Question about 2001 Citroen Xsara Picasso

1 Answer

Where do I put water in for radiator ? - 2001 Citroen Xsara Picasso

Posted by r_culshaw on

Ad

1 Answer

montehammons

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Citroen Master
  • 5,531 Answers

When engine is cool, take off radiator cap, and fill radiator. Then fill the coolant recovery container to halfway between the full cold mark and the full hot mark. Start engine (with radiator cap still off) and wait for the thermostat to open (upper radiator hose will get hot). Shut off engine, top up radiator, and put the radiator cap on. Fill the coolant recovery tank to the full hot mark.
You should mix the water and anti-freeze in a 50/50 mix before putting it in the car, you know. Cheers.

Posted on May 14, 2012

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Please show me about radiator tank cap for put water in my car's radiator(accent 2016). best regards


hyundai accent 2016.. USA version

this is a picture of the engine bay

coolant color might be red if its an aluminum engine
square box is radiator cap

you follow the small hose below the radiator cap to find the
overflow bottle

26230457-kadxnn1cckc133uoz54yk0hs-3-0.jpg

Jul 03, 2016 | Cars & Trucks

2 Answers

Can I damage my 1997 mercedes benz E320 by putting water 8n the radiator


You can put just water in the radiator if it is an emergency and you are in a pinch. These vehicles and their cooling systems require special coolant to fight corrossion and to lubricate the water pump and shouldn't be without for any extended period of time. Coolant will also raise the boiling point and keep the engine running cooler as well as protect from any type of freezing

Aug 03, 2015 | Cars & Trucks

2 Answers

What is the correct way to fill the radiator of a chevrolet venture The low coolant light came on then started flashing but the radiator is full of water but has no anti freeze is this the problem


Hi there!
First.- with the engine off and cool, put a flush and drain radiator cleaner run the engine for 10 minutes, turn it off, let it cool down.
Once the engine is not too hot, open the lowest hose of radiator while you put water in the main mouth of radiator.
Once you see the water flushing clear, put the hose back and then fill it with special GM antifreeze, (the one is orange color) put all gallon into it and the rest of water, LOOK FOR THE ONE YOU CAN ADD WATER, THAT'S THE BEST FOR YOUR VAN... Good Luck!

Jun 30, 2011 | 2000 Chevrolet Venture

2 Answers

How to drain and flush radiator


at the bottem on the left or the side there is a small key like screw ( righty tighty lefty lucy } then u must remove the radiator cap and also remove the themastate be sure to attach the therma housing and hose and unatch it at the top of the radiator the put water hose in the open cap area and flush for 20 mins turn on engine and let run for 2 min and repeat flushing untill all antifrez desapears. be sure to put every back tack pitchures as you remove so to put back the same way it might be good to get new thermastate

Jun 25, 2010 | 1998 Ford Taurus

2 Answers

2001 kia sportage is over heating but has no leaks. the radiator has been flushed but is very rusty inside. The water is rusty inside the radiator. We have checked the resevoir, it is fine. the water...


Rusty is from running a bad or no mix of coolant. (PH level is off) You may have a water pump that has corroded impellers, and can't move the coolant as well any more. I would start by making sure to flush the engine block again, and make sure you flush water through every possible hose, and where you can get at it.

Jun 14, 2010 | 2001 Kia Sportage

1 Answer

HOW DO YOU FLUSH THE RADIATOR IN FORD MONDEO ST 24


Well you take out the down hose,all the coolant in the radiator will go, remove the radiator cap put a water hose in the radiator,then open the tap .Let the water flows until you see clear water going out from the down hose.When finish put back the down hose like it was,then put your coolant in the radiator,then it is finished the flushing.

Jan 08, 2010 | Ford EXP Cars & Trucks

1 Answer

Water pump


Hello drain the water from the radiator by removing the hose from the radiator to the water pump,after having taken out the hoses,then unscrew the bolts that hold the water pump.After having taken the pump,clean the surface where the pump is fitted on the engine.Now when putting,the new pump,put a clear layer of silicone gasket on the surface where the pump will fit to prevent leakage,now you screw the bolt to the same torque,then after put the hose back like it was before,fill your radiator ,do not put the cap now,because of an air lock in the water circuit,start the engine,you will see the water level lower,fill it to its level,then put the radiator cap.Hope that help you in changing the pump,good luck

Dec 26, 2009 | 2000 Nissan Maxima

2 Answers

How to flush the radiator


on the radiator there is a bolt on the the bottom of the radiator,u must unscrew it ,this is point to service the radiator,well you have already unscrew that bolt the water in the radiator will go out,then take out the radiator cap then put a water hose in the radiator now see the dirt going out from the service point,let the dirty water goes until you see clear water goes out ,now you can close the water tap ,screw the bolt,the service point,by then u can put an antirust solution in the radiator,and fill the rest with water, put the radiator cap,and your radiator is up to date

Aug 22, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Coolant is not ciculating and not leaking it is blowing back in can i had new hose and thermostat housing put on is it air locked?


When engine is cold, take out the thermostat. Put back everything add water as needed to the radiator, leave the radiator cap out. Start the engine be careful stand in front of the radiator and where the radiator cap goes watch if the water is circulating rev it slowly and the water should circulate faster. If it is not circulating the radiator maybe clogged, inside the cylinder head where coolant circulates might be clogged or the water pump is not working.

Jul 15, 2009 | 2001 Ford Focus

1 Answer

Overheating 2001 pontiac aztek


remove coolant.remove thermostat remove bottom radiator hose to water pump.put a empty container under the radiator.take a water hose put it where thermostat goes flush out the rust in block.watch the water as it come out the water pump .if stream water is small keep flushing until you get a study sream of clear water. also flush out radiator. lower water pressure dont flush radiator it with high water pressure you could burst it. make clean the over flow jug .make sure it not stopped up.put in a new thermostat and radiator pressure cap. fill radiator with half antifreeze and half water.bleed the coolant system.

Apr 05, 2009 | 2001 Pontiac Aztek

Not finding what you are looking for?
2001 Citroen Xsara Picasso Logo

2,045 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14847 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...