Question about 2000 Ford Windstar

1 Answer

No start Need fuel presure specs. At ignition on and running then fuel above 2000 rpm's?????

Posted by rbulldog965 on

  • rbulldog965 Nov 20, 2008

    I have not been able to look at the veh yet. It was relayed to me that it turns over but no start. So just incase I wanted to know the fuel presure readings at key on. I will do my prelimminary checks and if need be get back to you. I do appriciate your help.



1 Answer


  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 20 Answers


2000 Ford Windstar Fuel Pressure Specifications:

Key On, Engine Off-- 35-45psi

Engine Running-- 28-45psi

Note- whenever you have an 'Engine Cranks No Start' condition you want to check for spark...

Posted on Nov 20, 2008

  • Anonymous Nov 20, 2008


    We can continue to help if you let us know what problem you are having... the more relevant detail the better.



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 91 s10 4x4 4.3 turns over no start has spark good fuel presure but no fuel coming out of injectors pore case down carb.wants to run. Had bad i.c.m. but replaced with good one .and new computer

If voltage to fuel injectors but no ground, have to check ignition module. The purple wire with white tracer carries rpm signal from distributor to computer, engine cranking, dc pulse on that wire, if nothing, check ignition module. W/o rpm signal, the computer won't ground fuel injectors.

Aug 03, 2017 | Chevrolet S 10 Cars & Trucks

1 Answer

The engine is slow to response at low rpm. above 2k rpm the engine response return to normal. spark plug, plug wire and ignition coils had been replaced, but the problem still persist.

Have you run a fault code test on this? Is the fuel pressure within specs under a load? Have you tried cleaning the MAF sensor heated wire?

Jul 21, 2016 | 2005 Hyundai Getz 1.6

1 Answer


it was related, ignition system..
you have to check ignition coil(pack).
improper distribution engine runs rough.

May 27, 2013 | Cars & Trucks

1 Answer

2000 jaguar xj8 intermitant fuel problem

You are dealing with a intermittent fuel pump problem can be the pump itself or bad connections. Here is the main concern for the fuel pump to turn on the ECM must recieve a RPM signal from the crank position sensor this signal must be recieved at the ECM greater than 250 RPM if it is not the fuel pump will not turn on. The use of a labscope works here or a generic scan tool with live data will show this. This problem necessarily gives engine codes.

Feb 23, 2012 | Jaguar XJ8 Cars & Trucks

1 Answer

When i try to start my 99 vw passat gls v6 it will barely start and stay started for possibly 5 sec with no presure on gas pedal if i keep my foot on the gas it will stay running but the rpms wont rise...

it hard to say there few things that could cause this but sounds like it a Fuel issue
Possible bad fuel pump totallly clogged fuel filter bad injectors Out of gas etc.
first thing you need to do is check your fuel pressure ( I bet it be low ) if it low check fuel filter if fuel filter good replace fuel pump
If Fuel pressure is within Specs then test the injectors
if Fuel pressure is ok and injectors test out ok then check ignition system (spark plugs, coils, module etc)

May 11, 2011 | 1999 Volkswagen Passat

2 Answers

2000 blazer will start and idle fine. but wont take fuel. the rpm will run up to 2000 after 2000 it looses power.i have checked the igntion/fuel presure/replaced throttle postioning sensor/replaeced fuel...


GAS-------INTO-------JETS---into---------ENGINE-----LOW RPM

Feb 09, 2018 | 2000 Chevrolet Blazer

1 Answer

2004 150 new fuel pump, enigine starts but dies, wait 5 mins. starts dies, unhooked fuel line very little gas

check the fuel presure reg but first check fuel ammount place fuel line un hooked in 1 galon glass jar turn ignition to run position container should fill quickly mesure fuel amount from single cycle call dealer ask what flow amount should be with single purge cycle
this will tell you if pump or filter are problem it will allow you to see if fuel filter is pooched and **** is bypassing also or if it is pluged

if results proper or close to dealer spec check fuel rail for bad fuel presure regualor if reg bad there will be little or no fuel presure even during purge cycle if flow high and finger cant hold presure if is usually fine and reg is bad pick up new reg from salvage it will cost 5 - 20 bucks and if a likely culprit

Jan 22, 2010 | 2004 Ford F150

2 Answers

Turn the key on and the starter will not engage.

check fuel pressure.if not above recomended spec. replace fuel pump. for starting have solenoid 0n starter checked.

Jan 26, 2009 | 1994 Cadillac Fleetwood

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides