WHERE IS THE EXACT ENGINE NUMBER LOCATION OF KIA SPORTAGE R2 2006 MODEL

In the 2008 Kia Sportage, the purge evacuation (EVAP) solenoid is typically located near the charcoal canister. The exact location may vary slightly depending on the specific engine configuration and optional equipment, but here is a general guideline:

1. Locate the Charcoal Canister: The charcoal canister is a component of the EVAP system and is responsible for storing fuel vapors. It is usually located in the rear of the vehicle, near the fuel tank or in the engine compartment. The canister is a cylindrical or rectangular-shaped container.
2. Find the EVAP Solenoid: Once you have located the charcoal canister, look for a smaller component connected to it. This component is the purge evacuation (EVAP) solenoid. It is typically a small plastic or metal device with electrical connectors and vacuum hoses.
3. Follow the Hoses and Wires: Trace the vacuum hoses and electrical wires connected to the charcoal canister to locate the EVAP solenoid. The solenoid may be connected directly to the canister or positioned nearby.

Please note that the exact location of the EVAP solenoid may vary slightly depending on the specific engine and emission system layout of your 2008 Kia Sportage. Consulting the vehicle's service manual or contacting a Kia dealership may provide more accurate and detailed information tailored to your specific model.
It's important to exercise caution when working with the EVAP system and its components, as they are part of the vehicle's emission control system. If you are unsure or uncomfortable performing the task yourself, it's recommended to seek assistance from a qualified technician or a reputable automotive service center. They have the expertise and tools to locate and service the EVAP solenoid properly.

The turn signal flasher on a 2014 Kia Sportage is typically located in the vehicle's fuse box. The exact location of the flasher will depend on the specific make and model of your Sportage, but it is generally located near the steering column or under the dashboard.
Here are the steps to locate the turn signal flasher:

1. Locate the fuse box: The fuse box in a Kia Sportage is typically located under the dashboard on the driver's side of the vehicle.
2. Identify the flasher: Once you have located the fuse box, look for the turn signal flasher, which is typically a small, rectangular box with two or three wires connected to it.
3. Test the flasher: Once you have found the flasher, you can test it by turning on the hazard lights and checking to see if the flasher is clicking. If it is not clicking, the flasher may be faulty and will need to be replaced.

Yes it is high if it still does that when it is warm. Cold idle speed is higher. Perhaps they will slow it down at first service.

Typically, the idle speed will be set at a value in the range of 600 to 800 RPM, but the exact value will depend on the number of engine cylinders and whether the vehicle is equipped with a manual or automatic transmission.

Kia Sportage Engine idle speed is high Inspection Costs

Transmission Fluid Level Check Kia Sportage 1995 2002 2002 Kia Sportage 2...

Hope this helps.

where is the engine number location of kia sportage 94 disel

you'd have to remove the engine its on the back. $5 pls. thanks. ;)

UNDER THE HOOD .ON THE HOOD THEY ONLY MADE 2 ENGINE SIZES THAT YEAR V6 WHICH IS A 2.7 AND A 4 CYLINDER 2.0 LITRE

Find the engine identification tag. Attached at the factory, this tag is normally found on the engine block around the coil bolts. The top line of the tag identifies engine size and model year.

Search the block for the engine block casting number. The numbers are raised, not stamped into the block and consist of seven numeric digits. The digits can be located on either side of the block. The seven-digit number may be followed with a dash and further numbers. These are change codes and are not normally necessary to identify the engine.

EX.:

Locate the casting date is located on the block. It is in standard date coding, 2.25.93, for example and may be located on either side of the block, but is commonly located on the driver's side of the block, above the freeze plugs. The example 2.25.93 decodes as February 25, 1993. The casting date may be near the casting clock, which designates the hour the block was cast. Magnum engines were manufactured from 1993 to 2002, so verifying the date code helps identify the engine.

It's at the front of the engine, RH-side.
Look in http://www.kiatechinfo.com after registering. You can find the manual there.

you'd have to remove the engine its on the back.