Question about Chevrolet K2500

Open Question



Posted by Anonymous on


5 Related Answers

Patrick Dennehy

  • 104 Answers

SOURCE: Remove me Steering wheel bmw 1999 e46 3 series

Disconnect negative battery cable. Locate airbag retentions on back of steering wheel. Unbolt or unclip retention devices, and release airbag. Then: Unplug airbag electrical connector. Remove nut or bolt in center of steering wheel with pneumatic impact wrench if necessary . Using appropriate steering wheel removal tool kit, carefully remove steering wheel, paying attention to associated wires, etc. Unplug anything not accompanying wheel, or that is in the way. Pay close attention to any rods, or contact pieces associated with the horn button(s.) Replace these upon reinstall. Reverse order to install including tightening center bolt to 35-55 ft-lbs. If this is your first stg wheel removal, try an old chevy, preferrably someone else's! If inexperienced, don't risk bruising your favorite Bimmer!!! Hope this helps you make your decision. Tater Todd

Posted on Jan 28, 2009


Carlos Rojas

  • 119 Answers

SOURCE: 2000 jetta need to remove steering wheel

This is not an easy procedure, especially since you've never done it before. With the wheels in the straight ahead position, look at the back of the steering wheel, you'll see two holes. One at 9 o'clock and one at 3 o'clock. You stick a small flat blade screwdriver in the first hole and you pry on the retaining spring while gently pulling on the airbag until it releases. Repeat on the other side. I'm a professional mechanic and the first time I did it, it took me over a half hour to figure it out. Now I can do it in less than a minute. Might want to take it to the dealer.

Posted on May 21, 2008


Ricardo Loranca

  • 552 Answers

SOURCE: Steering loose

at the end of the steering wheel there is your steering gear box on the top of the gearbox in the middle you will see a screw and a nut you need a wrench to lossen the nut and a screwdriveer to tighten it up. maybe your front end is loose you should have that checked out

Posted on Dec 05, 2008

SOURCE: Remove the steering wheel or airbag from a 2004 Volvo XC90?

You need a steering wheel puller. You may be able to rent this from your parts house. Disconnect the battery for no less than 1/2 hour before disconnecting the air bag or the air bag could deploy. Place air bag facing up or it could become a projectile if set off.

Posted on Aug 14, 2009

Sabo Gerovski

  • 271 Answers

SOURCE: Need to remove the steering wheel so i can replace

Disconnect the battery negative/earth/.Wait for at list 10 minutes to deactivate SRS airbags.Then remove the drivers airbag useing 5 mm allan key behing the steering wheel.There is two holes.Disconnect carefully the airbag.24mm socket to unscrew the steering wheel.Pull out the steering wheel.Disconnect the plugs of the switches.There is 3 screws/flat screwdriver/ Thats all

Posted on Jun 27, 2010

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove steering column cover

hi most mercs of this age are mostley the same where the steering wheel is look underneath that where your peddles are that is a large panel with around 7 to 8 screws keeping it in place remove this pannel when this is removed you should be able to see more screws keeping the steering colum plastic in place you may also need t remove the steering wheel first disconect battery as the srs light will come on and will need reseting if not behind the wheel there are 2 screw holes which are small star keys this removes the air bag once air bag is removed the steering wheel not will be there hope this helps

Aug 30, 2014 | 2000 Mercedes-Benz SLK

1 Answer

Steering colum goes up and down without moving the lever. need diagram to show entire colum

This is a common problem for this type of steering gear setup. What has happened is we tend to pull and put pressure on the wheel as a grab handle to assist or help ourself to get in/out of the drivers seat. There is a ball and socket that moves when unlocked, this ball/socket/spring is held together with 4 bolts that work loose over time when we use the wheel this way. It is a hard job to fix it. Due to the air bag and the problems that the air bag can cause I would suggest to you to have it done by a good shop. But just to get you in the ball park, you have to remove the steering column, So, you will have to take down all the covers, unplug all the wiring disable the air bag system, once you start you have to take care that you do not damage any of the delicate wiring to the air bag. You have to remove the wheel, the multifunction light switch, the cruse wiring, the wipers. Then take the connection loose from the rack and pinion outside the firewall. There are some good manuals to get that can help if you are set on doing this job. That would be better than a diagram posted here too small to see.

Jan 13, 2010 | 1992 Pontiac Grand Am

1 Answer

Starts on runs then dies and getting a no bus flashes on

this means no communication with the ecm. you have a power loss issue. check the common easy one.go in the engine compartment fuse box and look for a BOLTED juntion on the incoming power supply to the box. they lossen up alot and get corroded and burnt from arcing. clean tighten and try. if not then you have wireing gremlins elsewhere common too is in the steering colum but with the air bag circuits there i cannot advise you on this and will need to go in for service. good luck!

Sep 03, 2009 | 1999 Dodge Durango

1 Answer

Replacing a Cruise Control Switch

Ford Taurus/Sable 1996-1999 Repair Guide
Steering Wheel
Removal & Instalation


Fig. 1: Remove the access covers for the air bag module retaining bolts


Fig. 2: Remove the air bag retaining bolts and...


Fig. 3: Carefully remove the air bag from the steering wheel to access the wiring connectors


Fig. 4: Detach the connectors...


Fig. 5: ... from the air bag module


Fig. 6: Remove the center bolt from the steering wheel


Fig. 7: Install a suitable puller and tighten the forcing screw to...


Fig. 8: ... remove the steering wheel


Aug 19, 2009 | 1998 Ford Taurus

1 Answer

Remove and replace the ignition switch on the steering colum

is it a tilt whell and does it have the air bag in? if so the switch comes out after pull the steering wheel and horn assemby and air bag off. Boom.

Aug 17, 2009 | 1998 GMC Sierra

1 Answer

Remove the steering wheel or airbag from a 2004 Volvo XC90?

You need a steering wheel puller. You may be able to rent this from your parts house. Disconnect the battery for no less than 1/2 hour before disconnecting the air bag or the air bag could deploy. Place air bag facing up or it could become a projectile if set off.

Aug 14, 2009 | 2004 Volvo XC90

1 Answer

1999 Chev. Monte Carlo steering wheel make's a scratchy slidding,

Either part you mentioned can cause this type of noise.

Apr 19, 2017 | 1999 Chevrolet Monte Carlo

2 Answers

I am still havun problems with my 1997 camaro rs, the back turnsignals work but the front doesn't i was asked to check the elays but that is not the problem if there are any other suggestions they would...

there is a big conector coming from the steering colum, and is goin to the turn signal switch turn the signal on and test that you have a blinking power, at two cables then turn the other side on and do the same, if you have not power on two cables per side then you need a new turn signal switch, just make sure not to test any thing with yellow color because that's going to the air bag and you might deploy the air bag.

Jun 15, 2008 | 1997 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides