Question about 2006 Mercedes-Benz ML 350

Open Question

Ml350 fault present stored in control module transmission (p0718)

Car stays in 1st gear does not select

Posted by Corne Louw on

Ad

3 Related Answers

RamTek

Ramy de Jesus

  • 377 Answers

SOURCE: Transmission problem in E230 Benz

What you need to check is the transmission release bearing because if there is a clearance on the release bearing you will encounter this problem and also check the transmission oil.

I’m happy to assist further over the phone at https://www.6ya.com/expert/ramy_d9e7ebea3891f482

Posted on Jun 08, 2009

Ad
tgv1501

Clutch

  • 870 Answers

SOURCE: MB E350 2007. I was

Well your car is under warranty my friend, and if I were you i would go and raise hell at the dealer,try to read your Warranty book that came with your Car. -:)

Good luck

Posted on Dec 24, 2010

Ad

Anonymous

  • 1 Answer

SOURCE: ml350 2003, the wipers aren't working, front and

I have ML350 SE and my front wipers stopped working overnight (back wipers are working ok). I changed the fuse but it did not help.

Posted on Jan 09, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 BMW 323ci 2.5l 6cylinder manaul transmisson 1st gear wont stay in gear. pops out and grinds so i just avoid 1st gear and take off in 2nd. What is causeing 1st gear to do that?


possible explanation is a failing bearing on the input shaft or counter shaft
possible alignment problem between bell housing and motor
( uneven tension of mounting bolts )
check drain plug magnet for metal bits

May 08, 2017 | BMW Cars & Trucks

1 Answer

My question is I have a Hyundai 2006 while im driving the car go to D and D1D2D3.when is in D1 it dnt wanna drive fast .I wanna know what cause dats my first car and I love the car .please help me


All transmissions start in a low gear that is not meant for speed. When it is in D1, the transmission stays in 1st gear and wont move to a higher gear by itself. When you select D2 it starts in 1 and moves to 2 and then wont move any higher.

May 26, 2015 | Hyundai Cars & Trucks

1 Answer

Problems selecting 1st gear peugeot 106 1.1 zest


If the clutch is a problem you will have difficulty selecting 1st only as the gears would be spinning from the engine revs.. I would say that the front input shaft (clutch shaft) bearing is failing allowing miss alignment of the synchros and not allowing proper engagement of the gears synchro rings. It means removal and repair to the gear box so the clutch can be inspected while the box is out.

Apr 08, 2013 | Cars & Trucks

1 Answer

My 92 honda accord will not go into 1st 3rd or 5th gear


check shift fork adjustment. make sure you bleed the slave cylinder.also check shift cable adjustment.

Apr 11, 2009 | 1992 Honda Accord

1 Answer

Hyundai Coupe gearbox ( not car in product)


hi there! i was a master tech 4 hyundai, first of all has the atf fluid been changed and at the correct level. or have you had the multifuntion switch checked? please feel free to contact myself and i will advise you as required with my exsperience

many thanks

Dominic Hill

Dec 09, 2008 | 1998 Hyundai Elantra

1 Answer

Need to know how to adjust clutch on 03 focus with 5 speed


hi are you saying you canno select 1st gear?? but able to select other gears and drive car ok ? your clutch is auto hydraulic adjust if you could offer more info on 1st gear unable select? it would give a better picture of what may be your problem? at the moment its sound like selector problem?

Nov 16, 2008 | 2003 Ford Focus

1 Answer

The gear stick has no resistance, I can only select two gears and it feels like Im stirring porridge when I do try and select a gear.


i'm unfamilar with the exact car but it sounds like part of your gear selection linkage is broken. This would be the part that is used to select the gears you can't select. I have seen some cars that use two cables, one for 1st and 2nd gear and the second for 3rd and 4th gear. I have also seen cars that use metal rods from the shifter to the transmission much like the cable setup, one rod for 1st and 2nd gear and the other rod for 3th and 4th gear.

Hope this in some way helps.

Nov 12, 2008 | Peugeot 405 Cars & Trucks

Not finding what you are looking for?
2006 Mercedes-Benz ML 350 Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

jalal

Level 2 Expert

178 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...