Question about 2006 Chevrolet Equinox

1 Answer

I need the wiring schematics for 2006 equinox

I bought 06 equinox wich had burn fuse box,, with wires disconnected,, I bought a fuse box from salvage car with 3 harness,, I tryed to connect the wires together but I got stucked with fews wich are the same colors and sizez,, need the schematics to get throught each wire ,, please need help

Posted by riad Loubar on


1 Answer

bob palmer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    Visited the website for 3 consecutive days.


    An expert who has answered 20 questions.

  • Expert
  • 33 Answers

Try this site autozone. they ahve a lot of wiring diagrams. jsut go down the list until you find your diagram.

Repair Guides Wiring Systems 2006 Power Distribution Schematics AutoZone...

Posted on Feb 03, 2018


5 Related Answers


Harry Daehling

  • 13 Answers

SOURCE: need wiring diagram for taillights on 2000 chevy venture van

d7d3cd6.jpg3a50d5e.jpg80738de.jpg8d3e722.jpg GOOD LUCK

Posted on Feb 08, 2009


Mike Butler

  • 6674 Answers

SOURCE: Chevrolet Blazer 2000 Wiring Diagram

Have a look here.

Posted on Feb 20, 2009


Mike Butler

  • 6674 Answers

SOURCE: 2009 chevy expres trailer wiring harness

Ask dealer if it has a towing package on it. If it does, you usually just pop fuse in under hood for electric brakes, and harness to adapt into is usually near or at rear bumper. Even if it doesn't have brake wire, you should still be able to install adapter at rear,for lights etc. which is available from dealer or auto supply places, then you may have to run electric brakes separate.

Posted on Feb 21, 2009


  • 121 Answers

SOURCE: 2006 chevy trailblazer heater blower motor not working

You might wanna check and make sure the heater switch didn't go bad. It could even be the blower motor itself.

Posted on May 06, 2009


  • 2 Answers

SOURCE: Right side trailer brake light does not work

Did yo check the fuse panel inside the truck its located on the drivers side dash , you have to open the driver side door, in there is a 10 amp fuse that is linked to rt trailer brakes and rt turn signal for the trailer, if the fuse is good there is a black box under the dash located on the floor on the driver side, just to the left of the break, thats where must of the plug in wire harness is for the trailer breaks!

Posted on Jun 10, 2009

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

MY MERCEDES BENZ C280 is blowing fuses. The brake lights weren't working. It smells like something plastic is burning. A Mechanic looked at it, he smelled the RELAY BOX, it smelled horrible.

He paid for a garage to fix it. Call a salvage yard and see what you can get the box/harness for. Some boxes are hard wired with the harness. Some aren't, plug/ bolt on harness. Hard wire is a pain. they go every where. Plug in's, just check the connectors for corrosion and being melted. Take yours apart first to see what you have.

Jul 24, 2015 | Mercedes-Benz C-Class Cars & Trucks

2 Answers

Replaced battery car will start but no power

try to disconnect the battery for about 20 minutes. hook it back up and make sure you have the positive and negative wires on the right terminal. wrong way can short and burn your entire electrical harness. Check the fuses.

Apr 21, 2014 | 2002 Toyota Camry Solara

2 Answers

I have a 1988 Dakota 4 by 4 the wiring melted from a hole in the exhaust header now im trying to replace it but I cant find exact year & model. any info on where to find or buy ? I need from fuses on...

go to any parts place and have them check your wiring harness as well as the engines brain box ...a melted hot wire can burn up everything ,,that is a huge expense ..But they can trace your 1 single wire and help you for a few bucks ..Advanced / Auto zone ..God Bless

Oct 17, 2013 | 1988 Dodge Dakota

1 Answer

2007 equinox head lights burn out all the lights go dim hit the casing and they go bright again changed the pig tales and it still does the same thing why ??

I have changed the head lights in are Equinox several times. They work great for some time I would say after 4 mouths 1 will burn out . The low beam. I will change both lights. again not touching the leans putting them in with a clean great then in about 3 mouths the other side low beam will burn out. Again taking both out. I bought the best you can buy lights put them in September. 1 day the 1 burned out the next day the other side burned out low beam. So on March 3,I put in 2 new one's. again crossing my fingers. I'm almost redy to go to the dealer on this one. any idea's. Need help with my 2007 Equinox in Pa. Thanks Roger

Feb 27, 2013 | 2007 Chevrolet Equinox

2 Answers

Where is the fan relay sensor on a 2005 chevy equinox

Check to see if COOL HI fan fuse under hood is blown if so replace, test wires voltage and fan motor.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day and Merry X-mas.

Dec 23, 2011 | 2005 Chevrolet Equinox

1 Answer

Old fuse box burned up completly

Hello, With good Comprehensive Auto Insurance you can probably get this fixed under fire coverage. It is worth asking about if you have that type of Insurance and most people do not realize that problems like this are covered even if the vehicle does not burn in flames.

If you can not get the Insurance coverage then you need replace the fuse box and wiring. Your best bet is to try to get a wiring harness out of a Salvage yard. Most of the time the wire loom is connected in big sections. So it may take several cars before you can make 1 whole harness.

You did not put the Year or Model of your car in with your request. If you have a onboard computer, your dash gauge grid, and many more parts may be bad. Usually the cause of the problem will be burnt end to end. It is really a matter of "Did the fuse let go fast enough?". And it is possible to make improper connections through the melting process which can completely bypass the safety feature of the fuse.

If you wind up doing this yourself, get a good Ohmmeter. I have tried Signal tracers which make a signal in a wire and have a listening device to track them. Its available at Home Depot and does not work well on wires that are tighty bunched. I have used one on a Cabin Cruiser and thats when I found out about tightly bunched wires.

I hope my solution is very helpful in getting this fixed. I know what you are going through as I had a car lite up on me while driving.

Mar 11, 2011 | Ford Ranger Cars & Trucks

1 Answer

Fuel relay burns out in my 1997 silverado 1500 4x4 350

search a salvage yard for a replacement unit take unit and wiring harness from salvage yard usually about 30 -40 bucks if u just replace the box and the wiring was burnt and or shorted than ur problem wont be fixed but if u can find a salvage yard replacement with the wiring harness then its basically a plug and play replacement

Feb 22, 2010 | 1997 GMC Jimmy

3 Answers

I own a 2007 equinox. I had the oild changed today. During the oil change they attempted to replace my drivers side headlight bulb. There was to much stuff for them to remove so they didnt replace the...

2008 Equinox steering quit. It was the mega 80 fuse, and a $6.00 fix. I have NEVER boosted anyone, so not sure what happened. Will see if it goes again but sure hope it was just a one time incident.

Nov 18, 2009 | 2007 Chevrolet Equinox LS New Cars

2 Answers

Blower for hvac will not work?

For an '06 H3: If the fuse is okay (in the underhood fuse block), pull out the HVAC blower resistor and check it for burnt connections. It's located right under the glove box in the air plenum, easily accessed, and has a red male 6pin(?) plug in it. Mine had a burnt terminal that fused the two together. I went to the Hummer Dealer, and bought the replacement resistor and wiring harness. Parts are #10397098 (resistor) @ $37.74 and #25867517 (harness) @ $32.90. Both were easily replaced for a total of $70.64 plus tax. Save yourself $106 per hour labor and do it yourself. Easy fix.

Jul 14, 2009 | 2006 Hummer H3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides