Question about 1984 Chevrolet El Camino

Open Question

Wiring diagram 1984 el camino

Marker lights

Posted by Anonymous on

Ad

5 Related Answers

rick_amick

Rick Amick

  • 73 Answers

SOURCE: EGR Valve

remove the vacuum line and either 2 nuts or 2 bolts holding it to intake manifold. clean gasket material from mating surfaces and reinstall.

Posted on Mar 25, 2009

Ad
rick_amick

Rick Amick

  • 73 Answers

SOURCE: Does anyone have a wiring diagram for an 86 El camino

You can pick up a Haynes manual on it at like Auto Zone and it has wiring diagrams in the back. Shows color codes on wires and where they run. Hope this helps

Posted on Mar 26, 2009

Ad
alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: horn wiring diagram

a 1965 camino,centre steering wheel horn push? remove the steering wheel and check the carbon brush that runs against the copper metal ring on the bottom of the steering wheel

Posted on Dec 24, 2009

gtyner

  • 280 Answers

SOURCE: Hi, I need a fan belt diagram for my 1984 El

You should be able to get the diagram from your local parts house.

Posted on Mar 15, 2010

Anonymous

  • 518 Answers

SOURCE: pulling check engine codes on 1984 el camino

Locate your aldl connector under dash near steering column. It should have 12 pin connector. Older cars had 8 pin connector. You can do either one. On 12 pin connector jump the last 2 pins, on top row, in connector with paperclip or wire. Turn on ignition till check engine light turns on. Count & write down how many times it flashes. It will flash for example 3 times stop then 1 time = 31 code. In older 8 pin connector jump the 2nd & 4th pins on top.

Posted on Jun 15, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 H2 HUMMER exterior lighting


check lighting relay and replace if necessary

Jul 07, 2008 | 2004 Hummer H2

2 Answers

Why would only one out of 4 marker lights work?


you are right all marker lights come off of one fuse, inside instrument panel, number 29, a 10 amp fuse my manual does not give a lamp number, it has a chart, head lamps (high) lamp 9005 60 w type a, headlamp (low) 9006 51 w type b, front marker lamps 5w type d, for the rear it says to use a lamp 7443 21.5 w type d, I do not use these, I have special lights on mine, hope that it helps

Mar 28, 2015 | 2007 Scion tC

1 Answer

Replace rear side marker light


I had this message sent to me to solve....THIS IS MY QUESTION THAT I ASKED....LOL....SINCE THEN; I'VE BEEN INFORMED THAT YOU HAVE TO GO THROUGH THE OUTSIDE TAIL-LIGHTS TO GET TO THE MARKERS
DOES ANYONE ELSE KNOW ANOTHER WAY?
I have stainless steel covers over my tail-lights and will have to remove the "adhesive" on the covers to remove the tail-lights...HELP!

Jul 05, 2014 | 2007 Chevrolet Corvette Convertible

1 Answer

Marker light replacement


you have to remove head light housing to replace marker light.look in owners manual in glove compartment it will show you how to remove head light housing to replace head light or marker bulb.

Jun 19, 2013 | Cars & Trucks

1 Answer

Brake light diagram for 72 el camino


I am sorry but we have no wiring diagrams for anything this age.

Aug 31, 2012 | Chevrolet El Camino Cars & Trucks

1 Answer

Where can i find a diagram for a 1984 chevy el camino fuse block?


The position and function of the fuses is normally marked on the inside of the fuse box cover and also in the owner's handbook. If you are looking for a particular blown fuse, work your way through the fuses looking for a blown one. It is not difficult.

Mar 13, 2011 | 1984 Chevrolet El Camino

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...