Replacement buttons for home link 2006

Take your remote and hold it up towards your rear view mirror or your visor whitchever is the one with 3 buttons of your homelink , also make shure that your opener has a program button which come in different colors depending on the year of the machine, if you have a program button on your powerhead of your garage door opener then you can mostlikely program your car to it! The button on garage door opener comes in different colors such as yellow,green ,orange, black, grey and black ! make shure your opener has one of these buttons! Now take your remote and point it within a few inches of your visor/rearview mirror and hold the button down that oppens that door....now press the first button on your car mirror/visor until the door opens up , it take sometimes a few trys but remember to leave your car running while doing this and have it outside the front of your garage door while doing this!

Thanks filter4991;
1. Press and hold button on car's rearview mirror
2. Press and hold button on garage door opener's remote control.
3. Light on Rearview mirror will flash rapidly.
4. Release both buttons.
5. Locate learning button on garage door opener (generally this can be found by tracing the antennae to where it is attached to the unit.)
6. Press and release "Learning button"
7. Press and release rearview mirror button repeatedly until garage door opens/closes but it should work the first or second time.

Worked on Genie Intellicode and Hyundai Tuscon

Sounds like the linkage may have been detached when the mirror was replaced.

Push and hold the two outer buttons until the LED flashes fast Approx (15 seconds) then hold your garage opener up to the mirror or visor and push and hold any button 3 or 4 seconds on the opener Now the Home Link is programed. With the car safely away from the closing garage door find and push the garage openers red programming button (on the motor assembly somewhere that gives you about 30 seconds to push your cars home link button so the garage opener learns the button you want to use for that door the other two buttons can be programed for other doors or house light controler gate opener in the same manner

Things You'll Need

• Remote garage door opener

Suggest Edits

1. • 1

     Turn your Chrysler vehicle off and press and hold the two outside buttons on your onboard opener system. Release the buttons once the red indicator light begins flashing. This will erase any previous codes programmed to your system.
     

   • 2

     Hold your garage door opener remote two inches away from the onboard system.
     

   • 3

     Press and hold the button you wish to program on your onboard system and the open button on your remote simultaneously. Release the buttons once the indicator light on the onboard system begins flashing.
     

   • 4

     Press the training button on your Chrysler's system until the light glows solid. If it does not glow solid, continue to the following steps.
     

   • 5

     Press the "learn" button on your garage door remote, located near the antenna wire on the back or side of the system, and return to your vehicle.
     

   • 6

     Press the training button on your on board system, hold it for two seconds and release. Repeat the press/hold/release step two more times and your remote will be programmed and ready for use.
     

Read more: Instructions for a Chrysler Garage Door Opener ' eHow.com http://www.ehow.com/how_6201533_instructions-chrysler-garage-door-opener.html#ixzz1gQrTzTSH

Hyundai TSB 08-BE-012

PROCEDURE:
1. For first time training, press and hold the two outer HomeLink buttons, releasing
only when the HomeLink indicator light begins to flash after 20 seconds.
NOTE: Do not perform this step when training the additional HomeLink buttons.
2. Position the hand-held transmitter 1-3 inches away from the HomeLink mirror,
keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired HomeLink button
and the hand held transmitter button.
DO NOT release until the HomeLink indicator light flashes slowly and then rapidly.
When the indicator light flashes rapidly, both buttons may be released. The rapid
flashing indicates successful training and the procedure is complete. This also
indicates that the garage door opener does not use rolling code technology.
Note: The garage door may open or close during this step.
Steps 4 through 7 are only necessary if the HomeLink button appears to be
transmitting after step 3, but the garage door does not operate.
4. Press and hold the trained HomeLink button and observe the indicator light.
If the indicator light is solid/continuous, training is complete and your device should
activate when the HomeLink button is pressed and released.
If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light,
proceed with the following training instructions for a rolling code device. A second
person may make the following steps quicker and easier. It is recommended that a
ladder or similar device be used to obtain access to the motor housing. Do not stand
on the vehicle to perform the next steps.
5. At the garage door opener receiver (motor housing) in the garage, locate the “learn”
or “smart” button (usually near the hanging antenna wire attached to the unit). If
there is difficulty locating the training button, refer to the garage door opener’s
manual.
6. Press and release the “learn” or “smart” button (the name and color of the button
may vary by manufacturer).
NOTE: Once the button is pressed, there are 30 seconds in which to initiate the
next step.

7. Return to the vehicle and firmly press and hold the trained HomeLink button for two
seconds and release. Repeat the “press/hold/release” sequence up to 3 times to
complete the training process. If successful, your garage door should open or close
during this step.
If the vehicle owner continues to have difficulty programming their HomeLink mirror,
please have them contact HomeLink customer service directly at 1-800-355-3515 or
www.homelink.com for further assistance.
PROCEDURE COMPLETE

Good luck!

There was a minor change for mine to work.. see below..

- you must park your Prius close to the gate opener, leaving it running (obviously not in the way of the gate closing)
- Hold the button the the mirror and then push your garage door remote button and hold until the light on the mirror starts to flasyh fast. THIS programs the button on the mirror, but not the garage opener - yet (this was key for me)
- locate the "learning button" on the opener itself
- press the "learning button" on your gate opener and then get back into the Prius within 30 seconds (more time than it sounds) and press the SAME Homelink button you just programmed above. I don't recall how long I held the pre-programmed button, but the light will flash as I recall.
- Then, when working the garage door, you may need to hold the mirror button for a good second for it to work - but I had tried for months to get mine to work, and finally after reading many posts, the above sequence worked on my 2008 Prius with my Lift Master, Security + rolling codes garage opener.

Just - program the button on the mirror with your remote FIRST.. the garage opener will not work.. then use the Learn button on the garage opener and the SAME BUTTON you just programmed.. and it worked great for me. Not programming the mirror button first will not work. Using only the Learn button will not work. You must program the mirror first with the remote, then use the learn button and the SAME button on the mirror. Hope this helps.

Scott 2008 Prius with Lift Master Security + opener.
-

1. Press and hold the two outside garage opener buttons located on rear view mirror until the red LED light blinks (could be 20 sec.)
2. Press and hold the middle button on the rear view mirror while holding a garage door remote 1-3 inches away from the mirror and pressing the remote button. Do this until the blinking LED gets noticeably faster.
3. Once programmed - use the garage door opener on the mirror thru 3 cycles or more to verify.

Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

I checked Ford Focus mirror replacement and it seems to be the same. This is for the manual, unheated mirror.

Remove the mirror cover inside the door - slide a screwdriver behind the cover and pry loose carefully.

Remove the single 10mm bolt and the mirror comes free.
NB. Do not drop the bolt into the door.