Question about 2005 Chrysler 300

2 Answers

Chysler 300 code po335 - 2005 Chrysler 300

Posted by Gary Williams on

Ad

2 Answers

ZJ Limited

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 17,970 Answers

Hi there:
DTC P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include:
Vehicle may not start (see above)
Vehicle may run rough or misfire
MIL illumination

A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

Possible Solutions: using a scan tool, check if, when engine is running or cranking, that there is an RPM signal.
If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs?
If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay?
If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 27, 2012

Ad

Clifford Beard

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 1,975 Answers

Below is a descrption of what the diagnostic trouble code is (DTC) and the possible causes. There are MANY tests that really need to be done to actually verify the cause which is most likely the crankshaft position sensor but Chrysler is known for some electrical shorts or connection problems so the testing procedures should be done so you are not the buying parts for nothing. If you need help with these you will need basic tools and a digital volt/ohm meter and a fairly decent knowledge on how to read a wiring diagram. Feel free to reply/comment here or you can email me directly at [email protected] with all your information and I will be happy to help the best I can. Hope this helps a little anyhow.


chysler 300 code po335 - 2_27_2012_1_59_49_pm.jpg

Posted on Feb 27, 2012

Ad

1 Related Answer

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: 2005 CHYSLER CODE PO335 WHAT IS IT

Hi there:
DTC P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include:
Vehicle may not start (see above)
Vehicle may run rough or misfire
MIL illumination

A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

Possible Solutions: using a scan tool, check if, when engine is running or cranking, that there is an RPM signal.
If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs?
If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay?
If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 27, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car wont start ,no spark after replacing crank sensor


what maker of vehicle and motor are we talking about

EDIT Proton Arena 15i

something else is wrong
what ever is causing the no start does not have a code

yes PO335 right code and right part to replace6f1d8180-d547-4234-91c5-2b7b4c4df33f.jpg

car-wont-start-no-spark-after-replacing-r5w3vwqiamwa5yzrroebjr3v-2-2.jpg

Jun 22, 2016 | Cars & Trucks

1 Answer

Po335


replace sensor clear codes comon failure

Feb 12, 2014 | 2006 Chrysler 300

1 Answer

After accident chysler 300 any way to determine how fast car was traveling


the 300 could have been doing 55 -a t-bone to the rear axle will rip it apart and a p/u rears try to slid sideways on dry pavement don tak much to make it slide or spin sideways-and a 300 nose is all plastic and their computers are in engine bay cost more to repair so total is insurance choice of action-to determine if the speed is a factor u will need a lawer who deal with accidents one is that they usually have a person or a retired police office who are trained in accident reconstuction and they can request data from black box in other vehicle-but if ur the causing factor [improper turn -improper lane chnge-failed to yield right of way etc...]most lawyers wont take case

Apr 06, 2013 | Chrysler 300 Cars & Trucks

2 Answers

How can i tell which fuse is for what in my 300 chysler


here is an accurate diagram that you can use for the fuse box in a 2005 chrysler 300
franktilt_2.jpg

Feb 08, 2011 | 2005 Chrysler 300

2 Answers

Engine code $7E8: engine $7E9: A/T any idea what these are


$7E8 and $7E9 are sub menus for the Engine and Transmission. You need to select one and press enter. It will then give you the code for that sub menu.

Nov 06, 2010 | 2008 Dodge Ram Pickup 2500

1 Answer

Codes


PO725 = Engine Speed Input Circuit
PO335= Crankshaft Position Sensor A Circuit

Apr 19, 2010 | 2002 Nissan Altima

1 Answer

Code # 0843 Code # PO335


po843 is a hydraulic pressure valve in the transmission,that will have to be replaced.The code po335 is crankshaft position sensor a circuit malfunction.The sensor could be at fault here.

Mar 29, 2010 | 2002 GMC Sierra 2500HD

1 Answer

OBD malfunction indicator light status on stored diagnostic trouble codes po325, po335, p1336 . Car will not pass OBD test.


CODE PO325 - KNOCK SENSOR. CODE PO335 -CRANK SHAFT POSITION SENSOR. CODE PO336 - I DID NOT SEE CODE PO336.

Aug 28, 2009 | 1997 Nissan.5 Altima

Not finding what you are looking for?
2005 Chrysler 300 Logo

2,160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...