I want to replace my crank position sensor, but haven't found where it's at.
Have a 1991/second month dodge dakota with 5.2 4x4 and it does not have a crank sensor on the left side of the engine by the bell housing,there is nothing there no wires no sensor,there is no crank sensor on the front of the engeine,early dakota with 5.2 dont have a crank sensor.
have a 1991/second month dodge dakota with 5.2 4x4 and it does not have a crank sensor on the left side of the engine by the bell housing,there is nothing there no wires no sensor,there is no crank sensor on the front of the engine,early dakota with 5.2 dont have a crank sensor.
Replace the dist.its built into it
×
SOURCE: 2001 dodge 3500 van cam position sensor location
Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.
SOURCE: Crankshaft position sensor location - 1991 Dodge Dakota 5.2L
it is on the passenger side on the back off the motor.there are two allen head bolts or 13mm.it goes into the transmission and normally has rubber at the opening.you should be able to gets this from the top follow middle of valve cover on pass. side the go strait back toward the fire wall.please rate this answer.
SOURCE: 2001 dodge dakota crank no start
Just had that problem w/ my 01 Dekota, it was the resistor that used to be mounted on the firewall and easy to get to but that is now mounted low on the back of the engine jammed into a bey tight position. I couldn't get to it myself, so ended up taking it to neighborhood garage. Cost me about $150
SOURCE: Trouble Code 3255
Hi,
Thanks for using Fixya!
1. Cycle the ignition key ON-OFF-ON-OFF-ON within 5 seconds. To cycle
the ignition key ON means to turn it only as far as it takes to get the
radio to come on. It does not mean to turn the engine on.
2. Count the number of times the "check engine" lamp on the instrument
panel flashes on and off. The number of flashes represents the code.
There is a slight pause between the flashes representing the first and
second digits of the code. Longer pauses separate individual codes. For
example, flash-flash-flash [pause] flash-flash represents the code 32.
A code of "55" represents end of error codes. If this is all you get
then no error codes are stored in the computer. This is the normal
condition for a neon.
CODE Description of Trouble Code
11 Timing belt skipped 1 tooth or more from initial learned value,
Intermittent loss of either camshaft or crankshaft position sensor, No
crank reference signal detected during engine cranking
12 Direct battery input to PCM was disconnected within the last 50 key-on cycles
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD
relay output voltage at PCM, Fuel level sending unit volts out of
range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failure
So in your case, you are getting error 3255 right? so you are getting error 32 EGR system failure and 55 which is no other error found.
I hope you get this sorted out.
Have a great day sir.
- HotRatchet
457 views
Usually answered in minutes!
×