Oil pressure gauge going up and down

The computing system on your vehicle has no safe mode for running low on oil . The only thing that will happen is the check gauges light will come on.
The oil pressure gauge is an analog device that is located in the IPC. The oil pressure gauge is operated directly by the oil pressure sensor circuit. As the engine oil pressure changes, the resistance of the sensor and the current flow in the oil pressure gauge changes. The current flow in the oil pressure gauge causes the needle to move in order to appropriately display the engine oil pressure. A sensor resistance of 1ohms will display as 0 kPa (0 PSI) and a resistance of 88 ohms will display as 80 kPa (80 PSI ). The IPC also monitors the oil pressure sensor circuit and interprets the current flow in this circuit in order to determine when the engine oil pressure is too low. If the oil pressure is too low, the check gauges tell tale will turn on. The oil pressure sender is located on the left side of the 2.2L. The 4.3L engine, oil pressure sender is located at the top left side, near the distributor/high voltage switch.
Try disconnecting the battery cables an hold them together for ten minutes , reset ECM !

yes,it reads oil pressure only,if its out as long as it was working fine before it went bye bye your fine,you won't blow up engine or break down.

Hello, this problem is due to a failing stepper motor. The stepper motor is the motor behind the gauge that controls the
movement of the needle. When a stepper motor begins to go out it will cause the gauge needle to stick, skip around, stay
at zero or max out on the gauge. The only way to fix the problem is to replace the stepper motor with a new one. While
replacing one motor it is best to go ahead and replace them all as the others will go out in time as well. Youre cluster
will have one motor for each gauge. Here's a link to a page showing exactly how to replace a GM stepper motor and where
to get the correct parts to do the job!
DIY Finally How To Repair GM Instrument Cluster At Home Speedometer And...

the oil pressure gauge only gets a reading when the engine is runningas the oil is being curculated. when you shut the vehicle off it should go back to zero and be there until the vehicle cranks back up. i hope this helps

First off I wouldnt drive your car until you make sure that you have indeed oil pressure and that the gauge is a false reading, driving your car if in fact it has no oil pressure will severly damage your engine, but firstly i would check the oil pressure switch its located on the passenger side of the engine right back from the oil filter make sure the connector is clean and free from oil and corrosion if the connector appears to be in good shape take a paper clip and insert it between the 2 terminals inside the connector your oil pressure gauge should peak at 80 PSI that tells you that your gauge and all related wiring are good and in working condition, secondly remove the oil pressure switch and hook an manual oil pressure gauge up to you engine and start the engine the guage should have a oil pressure reading anywhere from 30 PSI to 55PSI depending on engine temperature if theres oil pressure on your manual gauge replace the oil pressure switch with a new unit, if you still have 0 PSI on your gauge then stop your engine immediatly and start looking at your oil pump and lubricating system for a problem.

First we would need to know when this occurs. Asuming the oil level is at the full mark!. If the pressure goes up during acceleration and down at idle when engine is fully warmed up, then this is normal. An engine requires 10 psi of oil pressure per 1,000 rpm ( ex. 20 psi at 2,000 rpm, 25 psi at 2,500 rpm, and so on ) . If the gauge is moving back and forth erratically at idle , i would say the gauge is bad. If it drops to 0 while accelerating I would say your oil pump is bad. If from time to time it seems to work and other times it seems not to work, I would say the oil pressure sending unit for the gauge is bad. If the pump failed you would start to here a Knocking noise from the engine in a short period of time. Use the above scenario's to narrow down what it may be.

Go to www.reliable-store.com and get all info on whether to repair or not, service it or not, and how to repair etc

You probably need a oil pressure sending unit it is located at the back of the engine and is a high failure

First we would need to know when this occurs. Asuming the oil level is at the full mark!. If the pressure goes up during acceleration and down at idle when engine is fully warmed up, then this is normal. An engine requires 10 psi of oil pressure per 1,000 rpm ( ex. 20 psi at 2,000 rpm, 25 psi at 2,500 rpm, and so on ) . If the gauge is moving back and forth erratically at idle , i would say the gauge is bad. If it drops to 0 while accelerating I would say your oil pump is bad. If from time to time it seems to work and other times it seems not to work, I would say the oil pressure sending unit for the gauge is bad. If the pump failed you would start to here a Knocking noise from the engine in a short period of time. Use the above scenario's to narrow down what it may be.

have them check the oil sending unit