Question about Chevrolet K2500

Open Question

How remove a door panel on 1994 chev k1500 truck

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 131 Answers

SOURCE: 2000 chev 1/2 ton

There is a special tool you can buy to help remove the quick fasteners. If you don’t want to purchase the tool you can use a flat blade screw driver. Be careful, they break easy.

Posted on Jul 10, 2008

Ad
alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: timing a 94 chev truck with a 350 engine with a timing lilght

engine idle and then check strobe light to mark on crank ,then slowly rev engine to check advance ,it should move

Posted on Jan 17, 2009

Ad
scottyoung56

Scott Young

  • 91 Answers

SOURCE: how do I remove the inside door panel on a 1999

there is two screws in the door handle then just pull the panel

Posted on Jun 16, 2009

super_guy

  • 1986 Answers

SOURCE: door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

hkidkw60

  • 1 Answer

SOURCE: remove thefront door panel on the driver's sidd in

you have 2 sicrews ( small) near the glass left and right to open & pull the panel upwards 1.5 cm then the panel becomes free .

Posted on Jan 02, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the door assembly on a 1994 gmc Sierra k1500


Hello,

There's in usually two ways to remove a car door. Either the hinges bolt to the frame of the car, OR they bolt to the inside of the door. In some cases they are welded in place, but that's pretty rare. If you can open the door, look in the door jam snd you should see the bolts. If you don't, try removing the interior door panel and look on the inside of the door (towards the front) and you should see them there. I'm sure the window frame will have to be in the "up" position. Good luck.

Mar 01, 2015 | 1994 GMC Sierra

1 Answer

HOW TO REMOVE EXTERIOR DOOR HANDLE 98 CHEV CHEYENNE


You are going to have to remove the inside door cover and get at it from that side---remove the door panel inside--they do sell tool kits especially for this task so not to damage clips etc.

Dec 17, 2012 | 1998 Chevrolet K1500

1 Answer

Cruise control on a 1994 chev truck want cut off how to cut it off


If you can't disable it by hitting the brake pedal, you may have to remove the fuse or disconnect the throttle cable.

Sep 26, 2012 | 1992 Chevrolet K1500

2 Answers

I have a 1994 Chev K1500 with a 5.7. I need to set the timing but the manual says to unplug the EST. The manual says the EST is in the panel inside the engine compartment on the firewall but I can not find...


the est wire is located on the passenger side on firewall behind a plastic cover in the shape of a T in the engine compartment.it is a single wire with a connector and is a tan wire with a black stripe on it.this is the wire you disconnect to set timing,you may have to pull it out of the wiring loom for easier access

Mar 02, 2011 | 1994 Chevrolet K1500

1 Answer

I need to replace the drivers side outside door handle on a Chev Z 71


YOU NEED TO TAKE THE INNER PANEL OFF THE DOOR AND THEN UNDO THE CLIPS OFF THE DOOR UNLATCH ROD AND THE DOOR UNLOCK KEY ROD. TAKE OFF THE TWO 10MM NUTS AND IT'S IN YOUR HAND. REVERSE TO INSTALL.

Sep 29, 2009 | 1998 Chevrolet K1500

1 Answer

I can't figure out how to remove the OEM door lock cylinder in my 1994 K1500 Blazer. I can get the handle unfastened, but not removed from the door. Also, can't figure out how to remove the retaining clips...


in order to remove the cylinder, You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.then you have to pull back the seal covering the door and remove the bolts holding the handle, door cylinder, and linkage assembly from inside the door

Aug 18, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

How do i take door panel off 1996 chev trk k1500


look for inlet covers take the screws out and then pull the panel from the bottom out first and the mirror cover thn pull baririer of and then you can get into there 3 screws on outside of door there are also retainers that are on the door rods it should just pop out from the bottom first

Jan 25, 2009 | 1996 Chevrolet K1500

1 Answer

CHEV 1500 2001 4X4 BATTERY GOES DEAD SITTING NEW BATTERY HAS DRAIN RADIO INSTRUMENT FUSE


you may have a bad aternator causing the drain start the truck and pull the pos cable off the battery if it dies then your alternator is bad

Aug 17, 2008 | 1994 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...