Question about Chevrolet Silverado 3500HD

Open Question

Wiring diagram for brake control 2007 chevy c5500 kodiak 8.1l

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 10 Answers

SOURCE: need belt diagram for 2007 chevy van

Check www.autozone.com.

Posted on Jun 14, 2009

Ad

Jose Morillo

  • 76 Answers

SOURCE: 1996 chevy caprice wiring diagram for cruse control

Are you trying to instll he cruse system in another car? BAD IDEA Are you trying to fix it in your car? first cause of fail is the third stop ligh blow

Posted on Sep 24, 2009

Anonymous

  • 1985 Answers

SOURCE: need a wiring diagram for a chevy s10. brake

your power starts at the brake light fuse,check with a test light,then proceed to stop light switch on brake pedal under dash,one wire will be hot when when you check it with your test light, the other won't be until you press down the brake pedal then the power flows through to the second wire,if no power to second wire replace switch,if you have power remove tail light bulbs and check for power in side socket.

Posted on Nov 26, 2009

Norman Green

  • 312 Answers

SOURCE: I need to wire an electric brake controller in my truck

you can either wire it straight or gm makes a connector that plugs into the drivers side floor . theres a box down there that has a cover over it and the gm connector plugs straight to it. but be careful because i have seen several times were gm wired it wrong the stop light plug is in the wrong spot.take a test light to ground touch each connector while pressing and releasing brake pedal the one that lights the light, is your stop light look on there connector and check to see if that plug is going to the red wire if not move the red wire to that spot. as for wiring it you have to do it this way. black wire goes to constent hot, white wire goes to constent ground , blue wire goes back to your trailer plug for your electric brake, and red wire as you know by now goes to the stop light.

Posted on Dec 27, 2009

iambanshee74

Kori Policy

  • 3489 Answers

SOURCE: I need a wiring diagram for a 1999 suburban

No problem, email me at [email protected]

Posted on May 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 gmc topkick c5500 fuse diagram


I have been unable to find the owners manul for thsie 5500 but zI have worked onthem and they use the same ele ctrical system as the 3500. So follow the link to the owners manual. https://my.gmc.com/content/dam/gmownercenter/gmna/dynamic/manuals/2007/gmc/sierra_3500hd/2007_gmc_3500_warranty.pdf

Jan 31, 2012 | Cars & Trucks

1 Answer

1991 chevy c-1500 brake switch wiring diagram for the 4 pin connector


red wire comes from fues box and white wire goes up steering colmn for the brake light turnsignal combonation. purple wire comes from fuse box and orange wire goes to cruise control unit for disengaugment

Jan 27, 2011 | Chevrolet C1500 Cars & Trucks

3 Answers

I have a chevy colorado 2007. The "serv tpm" light


TPM THAT MEANS TEMPOMAT CRUISE CONTROL.CHECK TO SEE IF BRAKE LIGHTS WORK.IF NO CHECK BRAKE LIGHT SWITCH FUSE. IF FUSE OKAY BRAKE LIGHT SWITCH FAULTY OR YOU HAVE OPEN WIRE FROM BRAKE SWITCH TO FUSE BOX.SEE YOUR BRAKE SWITCH DEACTIVATES THE CRUISE CONTROL SYSTEM.PROBLEMS WITH BRAKE PEDAL POSITION SWITCH WILL SET OFF CRUISE CONTROL WARNING LIGHT.IF BRAKE SWITCH OKAY.THE DEALERSHIP HAS TO DIAGNOSIS AND FIX PROBLEM.

Dec 03, 2010 | 2007 Chevrolet Colorado (Extended Cab) New...

2 Answers

Wiring 7 pin trailer plug for 1998 C1500 pickup truck Z71


Here is some information that I find useful when wiring trailer connectors, and the brake controller should be wired into the vehicles wiring according to the instructions that came with the brake controller and that identifies each wire from the brake controller.

Be sure that you solder all connections well for the best operation, and you should use 10 or 12 ga. wire for the Pos. (+) connection, and the ground or Neg. (-) connection, and you should run both wires all the way out to the battery, and about one foot from the battery on the Pos. (+) wire to the battery, make sure that you use a 20 or 30 amp Circuit Breaker and Do Not Use A Fuse.

The rest of these diagrams should help you to get your trailer properly wired up.





e701ee2.jpg

688461e.jpg

80dc266.jpg

47f1d3d.jpg

59ad859.jpg

444d9cf.jpg

May 15, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

2008 GMC C5500 factory wired for trailer harness (7 pin). I just purchased brake controller and am trying to find where the controller harness plugs into the truck harness. Looking under the dash. Plug...


You are probably going to find four wires together that do not have a plug on them. There should also be a tag taped on the wires showing that it is for the trailer. You will have to put a plug or some kind of connection on those wires.

Mar 13, 2010 | 2008 GMC Sierra 3500HD 2WD

1 Answer

Brake control hook up


off of your factory harness you will have a small brown wire and a small blue wire among the 5. Do not use the small brown wire, use the blue.

Mar 15, 2009 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

2007 chevy silverado hook up with tekonsha 4 wire brake control, chevy has 5 wires any suggestions


the fifth wire is most likely an auxiliary power wire, for if you wanted lights inside a trailer. (PLEASE RATE MY ANSWER!)

Mar 15, 2009 | 2007 Chevrolet Silverado 1500 2WD

3 Answers

Wiring diagram


Helpful Wiring Information when hard wiring your brake control:
Run two wires to the battery:
White - Ground
Black - Power
Blue - Run to Electric Brakes at the Rear Plug
Red - Run to cold side of brake switch off of the brake pedal (using a test light to find the cold side)
Note: Always wire the red wire to the heaviest gauge wire when testing cold side of brake switch.

You can view more info here. http://store.drawtite.com/brakecontrols.html

Jun 19, 2008 | 2007 Chevrolet Uplander LS Minivan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,469 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...