Question about Toyota Previa

1 Answer

HOW DO I REMOVE THE ROCKER COVER ON TOYOTA PREVIA D4D 2004 ONWARDS

Have removed all the 10 bolts the cover is loose and will lift up 1/2 inch but no more . do i have to remove the plastic connectors on the injectors?

Posted by JOHN MANNINGS on

  • Master of the House Nov 08, 2012

    How did you get on? I have same and need to replace valve seals.

×

Ad

1 Answer

jimcatherina

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 559 Answers

Remove the injector pipes and the guide tubes around them be careful not to crack them they will cause a bad oil leak

Posted on Feb 04, 2018

Ad

1 Related Answer

Jonah Oneal

  • 14092 Answers

SOURCE: number one injector came loose

REPLACE THE FUEL INJECTOR CANT REBUILT IT.IF YOU REMOVE FUEL INJECTORS FUEL RAIL YOU HAVE TO REPLACE GROMMETS AND O RINGS ON ALL THE FUEL INJECTORS IF NOT YOU WILL HAVE A INTAKE LEAK AT THE OLD FUEL INJECTORS SEALS.REPLACE THE FUEL INJECTOR YOU REBUILT THEY HAVE TO BE REPLACED.

Posted on Mar 02, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Purge solenoid location 2008 torent


Evaporative Emission Canister Purge Solenoid Valve Replacement
Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Disconnect the engine wiring harness electrical connector (4) from the evaporative emission (EVAP) purge solenoid.
Remove the oil fill cap. Lift upward and remove cover from ball studs.
The purge solenoid is under the plastic cover on top of the engine .
Disconnect the EVAP pipe quick connect fitting (1) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the EVAP pipe quick connect fitting (2) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service. Remove the EVAP purge solenoid bracket bolt (3). Remove the EVAP purge solenoid.

the purge

Sep 20, 2014 | 2008 Pontiac Torrent

1 Answer

Removal of radiator on a 2007 ford edge


Removal & Installation
  1. Drain the cooling system.
  2. Remove the cooling fan motor and shroud, as outlined in this section.
  3. Remove the front bumper cover, as follows:
    • Raise and safely support the vehicle..
    • Remove the 2 bolts from the top of the radiator grille.
    • Remove the 4 scrivets from the top of the radiator grille.
    • Remove the 3 lower pin-type retainers.
    • Remove the 6 fender splash shield screws (3 each side).
    • Remove the 4 lower screws (2 each side).
    • Disconnect the side marker lamp electrical connectors, if equipped.
    • Disconnect the fog lamp electrical connectors, if equipped.
    • Remove the front bumper cover.
    • Pull the corner of the bumper cover from the bracket.
  4. Disconnect the upper radiator hose and lower degas bottle hose from the radiator.
  5. Disconnect the lower radiator hose from the radiator.
  6. Lift and remove the tabs from the radiator support and position the radiator towards the engine.
  7. Remove the 2 A/C condenser bolts from the radiator and separate the condenser from the radiator. To install, tighten to 10 Nm (89 inch lbs.).
  8. Remove the radiator.
To install:
  1. Installation is the reverse of the removal procedure, noting the following:
    • Tighten the A/C condenser-to-radiator bolts to 10 Nm (89 inch lbs.)
    • Fill and bleed the cooling system.

Jul 27, 2014 | 2007 Ford Edge SEL

1 Answer

Bmw n42 removal of rocker cover 2004


if u have to ask you probably shouldn't go near it.there is nothing under there for a novice!
remove the filter ( 3 clips) from the back of the engine space
there are 5 (maybe 4) torex screws holding in the housing for the filter,remove housing
remove oil fill cap
loose cover should lift off
remove the 4 coil packs (they pull up off the spark plugs)
unscrew the 2 wires either side of the VVT motor
remove bolts(12mm socket) and rocker will pull off.
They can be a bi$ch to get back on.

Jun 04, 2014 | 2007 BMW 3 Series 328i

1 Answer

What tools do I need to replace my valve cover gasket?


Combination wrench set 1/4 " to 1" and/or 6mm to 19mm box-end & open-end or deep-well and short socket sets same size as wrenches with a 3/8" and 1/2" drive sets, Torque wrench, soft-faced hammer ( plastic or rubber ). The proper torque for valve cover mounting bolts is 85 inch-pounds for 1994 and later years.
Remove crankcase ventilation tube and hose from valve cover, Remove wire loom clips, note the locations of the studs.
Remove accelerator cable, kick-down cable and cruise-control cable from the snap in clips on top of valve cover, disconnect them at the throttle body .
Remove the three bolts and the control cable bracket.
Remove the valve cover bolts and lift cover off. If cover is stuck use a soft-face mallet to tap on the cover to break it loose.
DO NOT PRY ON THE gasket flange.
Contact me if you futher help.

Aug 28, 2013 | 1996 Jeep Grand Cherokee

2 Answers

How to install rocker arms on a Pontiac grand am 2001 V-6


Hi there:

Rocker Arms & Pushrods


Removal & Installation

3.1L & 3.4L Engines
Left Side

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system to a level below the coolant pipe on the front of the engine.
  3. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableSpark plug wiresHeater bypass pipePositive Crankcase Ventilation (PCV) valve and hoseRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm).Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).PCV valve and hoseHeater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).Spark plug wiresNegative battery cable
  3. Refill the cooling system.
  4. Start the vehicle and verify no leaks.




3_4_2013_5_26_48_pm.gif


Right Side
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableAlternator bracket on 2005 modelsSpark plug wires from the spark plugs and the upper intake plenum wire retainerPower brake booster vacuum pipe from the intake plenumAccessory drive beltAlternator, if necessaryIgnition coil assembly and Evaporative Emissions (EVAP) canister purge solenoid as an assemblyRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm) plus an additional 30 degree turn.Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).Ignition coil and EVAP solenoid assemblyAlternator, if removed. Torque the bolts to 37 ft. lbs. (50 Nm).Accessory drive beltPower brake booster vacuum pipe to the plenumSpark plug wiresNegative battery cable
  3. Start the vehicle and verify no leaks.





Hope this helps.

Mar 04, 2013 | Cars & Trucks

1 Answer

How do you remove the rear seats in a 1993 Toyota Previa?


hi

The rear seats have 1 x12mm or 13mm bolt securing it to the rear wheel arch.

Remove the cover over the bolt and unbolt the bolt 12mm or 13mm on the left and right side wheel arch

Then under each seat is a metal clip that holds the seats in place lift them up to unclip the seats, and then they can be removed.

cheers

Nov 16, 2012 | 1993 Toyota Previa

1 Answer

Oil pan repl. 1995 ford ranger 3 liter automatic


Oil Pan, Ranger SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Engine Lifting Sling 014-00036
Removal
  1. Disconnect battery ground cable. For additional information, refer to Section 14-01.
  1. Remove air cleaner outlet tube assembly by unclipping air cleaner clamp, loosening hose clamp at outlet tube, disconnecting intake air temperature (IAT) sensor and mass air flow (MAF) sensor connectors, and crankcase ventilation hose.
  1. Remove oil level indicator fan shroud retaining bolts. Position shroud over fan blade.
  1. Remove radiator support bolts. Raise and secure radiator to front core support.
  1. Remove engine mount nuts from studs.
  1. Unclip 42-pin connector from bracket and position it aside.
  1. Install suitable lifting brackets to left and right exhaust manifolds. Attach Rotunda Engine Lifting Sling 014-00036 (or equivalent) to lifting brackets. With a suitable lifting device raise engine approximately 50.8 mm (2 in). Install wood blocks between engine mounts and support brackets. Remove lifting device.
  1. Raise vehicle on hoist. For additional information, refer to Section 00-02.
  1. Drain the oil.
  1. Remove transmission insulator retaining nuts and install a jack stand to extension housing. Raise transmission about 25.4-101.6mm (1-4 in) to gain access for removal of oil pan.
  1. Remove transmission inspection cover.
  1. Remove starter motor splash shield.
  1. Remove starter motor retaining bolts and secure starter aside.
  1. If equipped, disconnect and remove low oil level sensor.
  1. NOTE: Oil pan fits tightly between transmission spacer plate and oil pump pickup tube. Use care when removing pan to avoid damaging either part.
    Remove oil pan bolts and lower pan.
  1. Remove oil pump retaining bolts. Lower and twist pump to allow the oil pan to lower completely. Remove the pump and pan assembly from vehicle.
  1. Remove and discard oil pan gasket.
  1. Clean the oil pan mating surface.
Installation
  1. NOTE: When using silicone rubber sealer, assembly should occur within 15 minutes after sealer application. After this time, the sealer may start to set up, and its sealing effectiveness could be reduced.
    Apply a 4.0-6.0 mm (1/5 inch) bead of Silicone Rubber D6AZ-19562-AA or -BA (or equivalent meeting Ford specifications ESB-M4G92-A and ESE-M4G195-A) to junction of rear main bearing cap and cylinder block and to junction of front cover assembly and cylinder block. Position oil pan gasket to cylinder block and secure it with Gasket and Trim Adhesive D7AZ-19B508-B (or equivalent meeting Ford specifications ESR-M11P17-A and ESE-M2G52-A).
  1. Install oil pump assembly and bolt. Tighten bolt to 40-55 Nm (30-40 lb-ft).
  1. NOTE: If oil pan is replaced with a new pan you must tighten new pan to spec then loosen and retighten.
    Position oil pan to cylinder block and install oil pan to engine bolts. Tighten bolts to 10-14 Nm (7-10 lb-ft).
  1. Remove jack stand and install transmission insulator retaining nuts. Tighten nuts to 85-118 Nm (63-87 lb-ft).
  1. NOTE: When replacing low oil level sensor, use a new metal gasket with a rubber O-ring.
    Install low oil level sensor. Tighten sensor to 20-34 Nm (15-25 lb-ft).
  1. Install transmission inspection cover and retaining bolts. Tighten bolts to 10-14 Nm (7-10 lb-ft).
  1. Install starter motor and bolts. Tighten bolts to 22-28 Nm (17-20 lb-ft).
  1. Securely install starter motor splash shield.
  1. Lower vehicle.
  1. Install lifting device and support engine. Remove wood blocks and lower engine back into original position. Remove lifting device and Rotunda Engine Lifting Sling 014-00036 (or equivalent). Remove lifting brackets from right and left exhaust manifolds.
  1. Remove support straps, lower radiator into position, and install radiator bolts to core support. Position fan shroud and install the retaining bolts. Tighten bolts to 6-8 Nm (52-71 lb-in).
  1. Install engine mount nuts and tighten to 98-132 Nm (72-97 lb-ft).
  1. Connect 42-pin connector to the bracket and install oil level indicator.
  1. Install engine air cleaner outlet tube assembly. Connect IAT sensor, MAF sensor, and crankcase ventilation hose. Securely tighten the hose clamp.
  1. NOTE: When battery has been disconnected and reconnected, some abnormal drive symptoms can occur while powertrain control module (PCM) (12A650) relearns its adaptive strategy. Vehicle may need to be driven 16 km (10 miles) or more to relearn strategy.
    Connect battery ground cable.
  1. Fill crankcase with correct viscosity and amount of engine oil.
  1. Start engine and check for oil leaks.

    Oil Pan Installation - Ranger


    a10121g.gif


    Hope this helps

Aug 14, 2011 | 1995 Ford Ranger Supercab

1 Answer

Starter needs to be replaced. Need instruction procedure for a do it yourselfer.


Hi, I have pasted the procedure from autozone.com below. Because this requires removal of the intake manifold, please be as sure as possible that your starter needs replacement. If you have any doubt, please let me know what your symptoms are and what troubleshooting you have done that led you to believe your starter is bad. Also, if you have any questions about the procedure below, please let me know. Thanks for using FixYa.


Removal & Installation


Disconnect the Negative battery cable


Relieve the fuel system pressure (you can do this by placing a rag over the schrader valve on the fuel rail and pressing in the valve stem--just be careful not to spray fuel on your eyes).


Drain the cooling system.


Remove or disconnect the following:


  • Intake manifold heat shield
  • Sight shield
  • Coil module connectors from the coil modules located on the valve covers
  • Positive Crankcase Ventilation (PCV) hose and valve from the valve cover
  • Fuel regulator vacuum tube
  • Vacuum tubes from the AIR solenoid
  • Fuel inlet and return lines
  • Fuel rail bracket retaining nut at the rear lift bracket
  • 2 pushnuts attaching the engine coolant heater wire and set it aside, if equipped
  • Fuel injector electrical connections
  • Fuel rail and injectors
  • Plenum duct clamp at the rear of the intake manifold, loosen
  • Intake manifold bolts and the manifold
Clean the manifold mating surfaces.


Remove or disconnect the following:
Starter electrical connectors Starter motor

jturcotte_1382.gif


Fig. View of starter motor removal and wires



To install:

Install or connect the following:

  • -S- terminal wire. Torque the nut to 35 inch lbs. (4 Nm).
  • Starter electrical connectors. Torque the nut to 89 inch lbs. (10 Nm).
  • Starter motor
  • Mounting bolts. Torque the bolts to 22 ft. lbs. (30 Nm).


jturcotte_1383.gif


Fig. Intake manifold torque sequence- 4.6L engines

  1. Grease the inside edge of the rubber plenum duct.
  2. Position the intake manifold by performing the following sub-steps:
    1. Place the rear of the intake manifold into the plenum duct.
    2. Place the front of the intake manifold downward on to the cylinder heads.

  3. Install the intake manifold bolts and torque to 89 inch lbs. (10 Nm) in the sequence illustrated. DO NOT torque the intake manifold bolts when the engine is HOT or at operating temperature.
  4. Make sure the plenum duct is fully attached to the rear of the intake manifold and tighten the plenum duct clamp to 20 inch lbs. (2.25 Nm).
  5. Install or connect the following:

    Fuel rail and injectors and tighten the rail retainers to 89 inch lbs. (10 Nm) Fuel injector electrical connections Alternator coolant pipe/surge tank pipe and position onto the fuel rail studs Engine coolant heater wire onto the studs and install the pushnuts, if equipped Fuel rail bracket retaining nut at the rear lift bracket and tighten to 89 inch lbs. (10 Nm) Fuel inlet and return lines Vacuum tubes to the AIR solenoid Fuel regulator vacuum tube Positive Crankcase Ventilation (PCV) valve and hose to the valve cover Coil module connectors to the coil modules located on the valve covers Sight shield Intake manifold heat shield Negative battery cable
  6. Fill and bleed the cooling system.

Mar 31, 2011 | 2002 Cadillac Deville

1 Answer

Number one injector came loose in 2001 toyota avensis d4d, removed injector pipes, wiring on injectors and rocker cover, tightened down injector, rebuilt and is now down on power.


REPLACE THE FUEL INJECTOR CANT REBUILT IT.IF YOU REMOVE FUEL INJECTORS FUEL RAIL YOU HAVE TO REPLACE GROMMETS AND O RINGS ON ALL THE FUEL INJECTORS IF NOT YOU WILL HAVE A INTAKE LEAK AT THE OLD FUEL INJECTORS SEALS.REPLACE THE FUEL INJECTOR YOU REBUILT THEY HAVE TO BE REPLACED.

Mar 02, 2011 | Toyota Camry Cars & Trucks

1 Answer

93 accord timing belt installation


  • Car jack
  • Jack stands
  • Torque wrench
  • Chain wrench
  • 3/8 inch drive ratchet
  • 1/2 inch drive ratchet
  • 10 mm wrench
  • 12 mm wrench
  • 10 mm socket (3/8 inch)
  • 14 mm socket (3/8 inch)
  • 17 mm socket (1/2 inch)
  • 19 mm socket (1/2 inch)
  • Timing belt
  • Balancer belt
  • Bottle of Liquid Paper

  • Disconnect the negative battery terminal. Using a ½-inch-drive ratchet and the 19 mm socket, turn the center bolt on the crankshaft so that number-one cylinder piston is at top dead center (TDC). You will know you ware at TDC when the mark on the crank is in alignment with the arrow on the timing cover.
  • Disconnect the cruise control connector and remove the cruise control actuator. Loosen the upper mounting bolt with the 14 mm socket. Use a 12 mm socket to loosen the lower nut then use a 10 mm socket to loosen the adjuster from the power steering pump and remove the belt.
  • Loosen the upper air conditioner mounting bolt using the 14 mm socket. Use the 12 mm socket to loosen the lower nut and adjusting bolt on the alternator and remove the alternator/AC belt. Remove the valve cover using a 10 mm socket.
  • Place the jack behind the left front wheel where the arrow is located indicating the jack location, and raise the vehicle. Put the jack stand under the subframe behind the jack, then lower the jack. Remove the left front wheel for easy access to the crank pulley. Using a block of wood atop the jack, place the jack under the oil pan and lift with slight pressure to hold the engine in place. Remove the side engine mount using a 17 mm deep socket.
  • Take off the dipstick, pipe tube and upper timing cover using a 10 mm socket.
    Then remove the timing belt adjuster rubber seal without loosening the adjuster nut. Take off the crankshaft pulley bolt. Use the chain wrench to hold the the crankshaft pulley while turning the crankshaft pulley bolt with a 19 mm socket. Use the 10 mm wrench and 10 mm socket to remove the bolts on the lower cover. Remove the lower cover and mark the location of the cam, crank and balancer shaft with Liquid Paper. Remove the balancer shaft belt and timing belt. Install the timing belt and the balancer shaft belt in the reverse order of removing them. During Installation of the crank pulley, coat the threads of the crank pulley bolt with engine oil and tighten it to 159 foot-pounds. Finally, adjust the tension of the power steering and alternator belts as well.

    Feb 03, 2011 | 1993 Honda Accord

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    198 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14850 Answers

    Mike

    Level 3 Expert

    4369 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...