Rear windows won't go down

change master switch first!

Most likely you have to replace the switch assembly on the driver side it probably got wet over the years from rain and snow and cause it to short out. Do not get a used part from a scrap yard because your end up with the same problems.

Window regulator is bad in the drivers door . Do you know what a regulator is ? The Trainer 24 Power Window Troubleshooting Do you know anything about automotive electrical testing ? How to read an use a wiring diagram ? Do you know there are two side to a electrical circuit ? B+ voltage an a ground side . Plus there is electronic control modules and class 2 serial data network involved . When you push the switch for a window othen then drivers window on the drivers door . a class 2 message is sent to the other doors modules . The correct module will then open it's window .
http://www.bbbind.com/free_tsb.html Check out free wiring diagram here .Enter vehicle info . year , make , model and engine size. Under system click on body & accessories , subsystem click power windows . Click search button , then click each link one at a time .

Most probably motor. Have someone push button while u hold ear to inside door and listen for motor to try and run.

Most time shot in dark as most will not make noise but sometimes you will hear a click letting you know that power is at least getting to motor.

rear oil seal if your not into mechanics you should take vehicle to a repair shop not that simple transmission has to be unbolted from engine remove flywheel etc. big job for some ppl. as far as the window goes sounds like a bad switch

You also have Circuit Breakers for your windows, Or your Master Switch ,You can Test the Driver Control Switch or the rear switches by removing the Switches and using the connector Plug and a Jump wire try jumping accross the wires,if they go up or down you could have a Bad Switch,if nothing moves more than likely your Window Motor is bad. BUT first CHECK your Circuit Breakers ,It could be Labeled as accessery Relay or circuit Breaker.

There is a control module in each door with connectors. I have already had one where the wiring in the connector was bad. This takes some troubleshooting, but sometimes moving things around while trying to run the windows will should you where the loose connection is.

it may need to be reset.

SECTION 501-11: Glass, Frames and Mechanisms 2001 Explorer Sport/Sport-Trac Workshop Manual
GENERAL PROCEDURES Rear Window Motor Initialization CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.

1. Start with the ignition in the OFF position.

1. Turn the ignition to the ON position.

1. Press the power rear window control switch vent button six times.

1. Turn the ignition to the OFF position.

1. Press the power rear window control switch vent button six times.

1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.

1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.

1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.

1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.

1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions.

------------------------------------------------------------------------------------

• The power rear window is inoperative (Explorer Sport Trac only)

• Circuitry.
• Battery Junction Box (BJB) fuse 3 (30A).
• Central Junction Box (CJB) fuse 20 (7.5A).
• Power rear window control switch.
• Rear window glass motor.

• Go To Pinpoint Test K .

------------------------------

The book says 1. remove power accesory switch panel by using suitable flat blade tool at front. 2. Disconnet electrical connections.
3. pry door handle plug by using small flat bladed tool
4.remove door trim handle mounting screws
5. remove door trim panel from retainers.Start at rear bottom corner and pry outward.
6. remove door panel.
KD does make a tool that will properly pry the door panel away from reainers. KD 3705 You might get by with a screwdriver.
One other thing you may need to have the window down to get the panel to come off. You will have to lift up on it once it is loose from the fastners.
Hope this helps you out.

i also have a rear power window that wont open..I just got the truck and it was like this when i got it... My windows work just fine but my rear sliding has zero responce when i press the button. Do you think its the 30 amp breaker?