Question about 2001 GMC Yukon Denali

Open Question

2001 gmc yukon door hinge replacement

How do you pull the existing hinge pin?

Posted by Frank Fulton on

Ad

5 Related Answers

short shadey

jeff r

  • 421 Answers

SOURCE: 2001 Blazer door hinge pins and bushing replacement

you need a special spring compressing tool to remove and reinstall the hinge spring and then its a matter of removing the door installing the new bushing and rehang the door with new pins ive tried doing this while leaving the door on the car trust me its just harder that way good luck and please rate -jeff

Posted on Sep 01, 2008

Ad

work4it1

  • 196 Answers

SOURCE: light replacement

Just reach behind the bumper and grab the light/electrical harness and twist is either way and then it should pull out put in a new 194 bulb and you are set.

Posted on Jan 08, 2009

Ad
MrScary66613

Travis Humphries

  • 1990 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000

No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 27, 2009

Anonymous

  • 6 Answers

SOURCE: u-joint repalcement for 2001 yukon xl

Mark your drive shaft coincidenly with the rear axle and tranny. Remove drive shaft. Press out the old u joints and press in the new. You will need a torch for heat and a lot of patience. Have fun!

Posted on Jun 20, 2009

Anonymous

  • 541 Answers

SOURCE: replace front left wheel berring on 2002 GMC Yukon

do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Posted on Jan 03, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the Bose system in a 2003 Yukon Denali have a fuse


yes open drivers side front door fuse access panel near door hinge side pull from bottom out look on back side of door for fuse location

If you need further help, I’m available over the phone at https://www.6ya.com/expert/mike_9693b5ad75773352

Feb 27, 2015 | 2003 GMC Yukon Denali

1 Answer

2001 honda passport front driver side door hinge is popping loudly when opening and closing, how do I repair it


You need to go to the nearest auto parts store like O'reilly and tell them you need a new door hinge pin for your car. The pin comes with llittle nit looking pieces. It is simple to put on but it will take time. But put the little pieces on top of the holes for the pin then slide the pin through the nuts and the problem should cease to exist.

Jan 17, 2013 | 2001 Honda Passport

1 Answer

Need to replace front door hinges (not just the pins). How are they attached?


they are attached with a silicone glue. Cut off with a razor knife. Then gently pull down on the door. They will pop loose.

Sep 14, 2010 | 2001 GMC Jimmy

1 Answer

Driverside door coming off or hanging low. big spring came out of door hing. back window hath won't lock.how do i fix rear driverside roter and caliper (replace). thanks


the door problem sounds like the door pins and bushings are worn out. this should be fixed asap because if it is let go the pin will cut into the hinge itself and then they may also need replaced. hope this helps!

Jun 08, 2010 | 2001 GMC Jimmy

1 Answer

Door pins


go to popular mechanics auto shop and look up door pins or hinge pins

May 10, 2010 | 2001 GMC Yukon XL

1 Answer

I need to replace the hinge pins in my 2000 yukon suv. I have a kit from NAPA, but I need some pointers on how to get the old pins out and install the new ones.


The pins are pressed in. The door must be opened and setting on a platform to rest on for security. The pins hold the door on your truck you know. You may have a coiled spring on one hinge. If so purchase a spring compressor at Auto Zone auto parts or any auto parts store. Have a center punch to hammer out the pins. I would remove one pin and replace it then go to the next one. The upper will have the most wear from the weight hanging from the door. Do both pins of couse to save the door lock from malfunctiong later. A sagging door will ruin a door latch in time

Apr 21, 2010 | 2000 GMC Yukon

1 Answer

How can i take off a 95 gmc yukon passenger door? what tools would i need?


If it's the left front door, the hinges are welded. There is a pin that goes in the hinge. You'll have to get a long punch and a hammer to drive the pins out. If you have a relatively long 3/8 socket, you can invert it so it fits over the top of the pin to get it started. Then as the head becomes visible, you can lock a pair of vice grips on the pin and tap it out. Sometimes a pry bar is enough to finish the job. There may be a special tool to get the pins out, but I haven't seen it.

Hammer
Long punch
Vice Grips
Long 3/8 extension
Pry Bar

Patience

Hope that helped. Thanks for using FixYa.

Mar 29, 2010 | 1995 GMC Yukon

1 Answer

2004 GMC Yukon XL Denali


if the hinges are loose making the door difficult to close the brass bushings in the hinge pins are worn
replace the parts to regain a perfect closure to your door
if not replaced the latch will go bad very soon

Mar 07, 2010 | 2005 GMC Yukon Xl Denali

2 Answers

Door hinges are noisy?


sounds to me like the hinge pins are worn out. These could probably be driven out with a drift and replaced with new.

Jun 02, 2009 | 2004 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1256 Answers

john h

Level 3 Expert

23515 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...