Question about 1995 Saturn Sl

Open Question

1995 saturn sl1 ignition won't release key

I replaced the ignition/key cylinder with new and key cannot be removed when cylinder is turned to the "lock" position. Op-tested both old and new cylinders outside of the cylinder housing and keys can be removed properly. I also inspected the housing to see if any mechanical parts of the cylinder appeared to be snagging and everything on the outside looks like it is working. Can anyone assist?

Posted by Richard Laycock on

Ad

5 Related Answers

Anonymous

  • 73 Answers

SOURCE: remove outside door handle on 1994 saturn sl1

lift up the door handle and look on the bottom side of the handle, you should see a small black retainer on one side, use something small to push in the canter and a small flat bladed screwdriver to remove retainer. then slide the handle to the front or to the rear to remove.

Posted on Mar 31, 2009

Ad

wekjo

  • 3911 Answers

SOURCE: How to replace driver side

Remove the inside cosmetic plastic panel at the front of the driver's window, there is a phillips head screw holding it on. You will have to have a very small allen wrench to take out the set screw holding the mirror adjuster knob mechanism into the plastic panel. Remove the three nuts you find under the insulation and the mirror will come loose. Reinstall in reverse order.

Posted on May 06, 2009

Ad
lilmikew99

michael

  • 122 Answers

SOURCE: car rpms go to 4 with no excelleration

if your rpm's are going up and down on there own i would have a scan done too see if the tps sensor is gone, this controls the idle, and other things as well

Posted on May 11, 2009

Anonymous

  • 74 Answers

SOURCE: 2002 S series Saturn remove and replace ignition cylinder

unfortunately your cylinder's guts exploded in the cylinder housing and you will need to replace both now

Posted on May 26, 2009

AstralTravlr

  • 9 Answers

SOURCE: 2002 Saturn Vue Ignition Cylinder lock problem

The keys on this vehicle have a problem with wearing down to the point where it's a pain to get them to work in the ignition cylinder. Examine your keys for wear and that may have been your problem since day one.
I have a 2004 Vue and I have the only key I got with it (used car) worn down to the point where it will no longer work in the back door and is a pain to use in the ignition cylinder. It also falls right out of the ignition cylinder when the car is running. I have a copy of the key that was made when I got the car which works just fine and doesn't fall out, and looking at the two side by side, you can see that Saturn's key has worn down substantially since I got it two years ago.

Posted on Jul 23, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I know if my ignition switch is bad ?


The electrical part or the key lock cylinder part ?
Ignition Key Cannot Be Removed from the Ignition Lock Cylinder
Did you review the Steering Wheel and Column Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Steering Wheel and Column Description and Operation

2

Verify the key cannot be removed from the ignition lock cylinder.
Is the key stuck in the lock cylinder?
Go to Step 3
System OK

3

Is the vehicle equipped with a manual transmission?
Go to Step 6
Go to Step 4

4

Turn the ignition key to the OFF position.
Can the key be turned to the OFF position and be removed?
Go to Step 6
Go to Step 5

5

Verify the adjustment of the automatic transmission cable. Refer to Shift Control Linkage Adjustment in Automatic Transmission - 5L40-E/5L50-E.
System OK
Go to Step 6
Ignition Can/Cannot Be Turned Off with Transmission in Any Gear
Operate the system.
Does the system operate normally?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 2

2

  1. Push the ignition lock cylinder control actuator release button which is on the underside of the ignition key cylinder.
  2. Turn the key to the OFF position and remove the key.
Were you able to turn the key to the OFF position and remove the key?
Go to Step 3
Go to Lock System Does Not Lock

3
  1. Turn OFF the ignition.
  2. Disconnect the ignition lock cylinder control actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the battery positive voltage circuit and the ignition key/shifter interlock switch supply voltage circuit of the ignition lock cylinder control actuator with a test lamp.
Does the test lamp illuminate?
Go to Step 8
Go to Step 4

Aug 20, 2015 | 2006 Cadillac CTS

1 Answer

Replaced old ignition with new one and the new ignition won't lock in place


If the ignition wont lock in place,just redo it but this time you need to realize that you install the key cylinder with the key in the ON postion,straight into the lock cylinder housing,aligning the retaining tabs,on the key cylinder with the hole in the lock cylinder housing.Then turn the key to the off position,

Aug 07, 2012 | 1997 Plymouth Grand Voyager

3 Answers

How to remove and install ignition switch


remove the steering coloum trim. Turn the key to run position, Press locking button on back of steering coloum housing assembly, Remove lock cylinder, Disconnect the ground strap from lock preload spring ( if equiped ) . Make sure key is still in run position when you reinstall.

If the key is non functional and you cannot turn to run then you will need the tool in this picture197ca25.gif

Aug 12, 2010 | 1997 Chevrolet Cavalier

2 Answers

I have a 99 voyager and the ignition will not turn how do I remove it


Here's a copy of a service bulletin on your problem.

I'll bet the dealer says $300 for parts and 2 hrs labor.:screwy:

Ignition Key - Will Not Turn And/Or Cannot Be Removed
NUMBER: 23-23-00
GROUP: Body
DATE: JUNE 30, 2000
SUBJECT:
Ignition Key Will Not Turn And/Or Cannot Be Removed
MODELS:
1997 - 2000 (NS) Town & Country/Caravan/Voyager
OVERVIEW:
This bulletin involves performing one or any combination of the following procedures; cutting a new ignition key, and/or adjusting transmission shifter cable, and/or replacing the ignition lock cylinder and/or replacing the ignition lock housing and switch assembly.
SYMPTOM/CONDITION:
1. Cannot turn the ignition key when attempting to start vehicle, this condition may be intermittent.
2. Unable to remove the ignition key from the lock cylinder.
PARTS REQUIRED:
AR(1)04778115 Key
AR(1)05003843AB Cylinder, Ignition Lock
AR(1)04690523 Assembly, Ignition Switch and Lock Housing
EQUIPMENT POSSIBLY REQUIRED:
Key Cutter such as Pentastar Service Equipment (PSE) IL-MK1-P2627 or
IL-ECM-100
T-27 Torx Bit
T-25 Torx Bit
T-10 Tamper Resistant Torx Bit
SR-706059 Lock Cylinder Build Kit, Pentastar Service Equipment (PSE)
DIAGNOSIS/REPAIR PROCEDURE:
DOES NOT REQUIRE HOISTS OR OTHER FULL SERVICE FACILITY SPECIAL EQUIPMENT. THIS REPAIR IS COMPATIBLE WITH DAIMLERCHRYSLERS MOBILE SERVICE PROGRAM.
SYMPTOM/CONDITION ONE
1. Ensure the steering wheel is centered and the vehicle is positioned on a level surface.
2. Disconnect the negative battery cable.
3. Insert ignition key into the ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
4. If the key does not turn, remove the key from the lock cylinder and rotate it 180°. Reinsert the key into the lock cylinder and attempt to rotate the key. If the key does not turn skip to step 14. If the key does turn make a new key.
NOTE: USE THE KEY CODE ON THE VEHICLE INVOICE TO CORRECTLY CUT THE NEW KEY. KEY CODES ARE ALSO AVAILABLE USING THE D.I.A.L. SYSTEM, MAIN MENU OPTION 13. DO NOT USE A KEY DUPLICATOR TO MAKE THE NEW KEY.
5. Insert the new ignition key into the ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
6. If the key turns, remove the key from the lock cylinder and turn it over 180°and reinsert the key into the lock cylinder. Attempt to rotate the key.
7. If the key turns, repeat steps 5 and 6 ten times. If the key continues to rotate smoothly the repair is complete. If the key fails to turn smoothly at each rotation attempt, continue to step 8.
8. Remove the ignition lock cylinder using the procedure outlined on page 8D-29 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005). DO NOT ATTEMPT TO DISASSEMBLE THE Lock CYLINDER.
9. Build a new lock cylinder to the key code on the vehicle invoice, using the instructions in the Pentastar Service Equipment SR-706059 Lock Cylinder Build Kit.
10. Install the new ignition lock cylinder using the procedure outlined on page 8D-29 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).
11. Insert the new ignition key into the new ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
12. If the key turns, remove the key from the lock cylinder and turn it over 180°and reinsert the key into the lock cylinder. Attempt to rotate the key.
13. If the key turns, repeat steps 11 and 12 ten times. If the key continues to rotate smoothly the repair is complete. If the key fails to turn smoothly at each rotation attempt, continue to step 14.
14. Remove the ignition lock housing and ignition switch as an assembly using the procedure outlined beginning on page 19-47 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).
NOTE: SKIP STEPS 13 AND 14 OF THE SERVICE MANUAL REMOVAL PROCEDURE SO THE IGNITION LOCK HOUSING AND IGNITION SWITCH ARE REMOVED AS AN ASSEMBLY.
15. Install a new ignition lock housing and ignition switch assembly, p/n 04690523, using the procedure outlined beginning on page 19-49 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).
NOTE: PRIOR TO PERFORMING STEP 2 OF THE SERVICE MANUAL LOCK HOUSING INSTALLATION PROCEDURE, INSTALL THEN REMOVE THE TWO LOCK CYLINDER HOUSING MOUNTING SCREWS INTO THE LOCK HOUSING MOUNTING HOLES TO CREATE THE THREADS IN THE HOLES.FAILURE TO CREATE THE MOUNTING HOLE THREADS PRIOR TO INSTALLATION TO THE STEERING COLUMN MAY CAUSE MISALIGNMENT OF THE LOCK HOUSING TO STEERING COLUMN AND DAMAGE BINDING OF STEERING COLUMN MAY RESULT.
STEPS 5 AND 6 OF THE SERVICE MANUAL INSTALLATION PROCEDURE FOR THE LOCK HOUSING ARE NOT NECESSARY FOR THIS TSB PROCEDURE.
WHEN PERFORMING STEP 9 OF THE SERVICE MANUAL PROCEDURE USE THE NEW LOCK CYLINDER THAT WAS BUILT IN STEP 9 OF THE SYMPTOM/CONDITION ONE DIAGNOSIS / REPAIR PROCEDURE OF THIS BULLETIN.
16. Insert the new ignition key into the new ignition lock cylinder and attempt to rotate the key to the start position and then the accessory position.
17. If the key turns, remove the key from the lock cylinder and turn it over 180°and reinsert the key into the lock cylinder. Attempt to rotate the key.
18. If the key turns, repeat steps 16 and 17 ten times. If the key continues to rotate smoothly the repair is complete.
SYMPTOM/CONDITION TWO
1. Check the operation of the shift lever. The shift lever should fall freely away from the driver when it is brought up into the Park position.
2. If the shift lever does not seat fully up and away from the driver the column will not allow the key to be removed.
3. If binding of the shift lever is discovered, adjust the transmission shift cable using the procedure outlined on page 21-114 of the 2000 Town & Country, Caravan and Voyager Service Manual (Publication No. 81-370-0005).

Jun 01, 2010 | 1999 Plymouth Grand Voyager

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

How to replace a lock cylinder on a 1992 ford explorer


Steps to remove and replace the lock cylinder To Remove the Lock Cylinder 1: Remove the cover UPPER/LOWER) from the steering column(usually 2 phillips screws in lower cover, directly behind the steering wheel. 2: Turn the key to the run position (the position before start). 3: Using a small diameter object (paper clip) slide the wire into the hole located underneath the ignition switch on the underside of the column. While pushing up on the pin in the hole, turn the key and pull outward. The tumbler should release and come out. 4: To replace, turn the key in the new cylinder to run. 6: Place the cylinder in the column where the old one came out. 7: Turn the key to the off position and the cylinder is now locked in place.

Nov 17, 2009 | 1992 Ford Explorer

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

1 Answer

2000 contour


for 98 contour issue. TSB 98-21-14 not covered by warranty

This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar)

Mar 09, 2009 | 2000 Ford Contour

1 Answer

1997 ford contour


this is for 98, but may apply if yours is late 97 build.

Article No.
98-21-14
  • IGNITION SWITCH - HIGH EFFORT IGNITION KEY INSERTION/REMOVAL AND/OR KEY CHIMES SOUND WITH DOOR OPEN AND IGNITION KEY REMOVED
Publication Date: OCTOBER 15, 1998
FORD: 1998 CONTOUR LINCOLN-MERCURY: 1998 MYSTIQUE
1999 COUGAR
This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar

Aug 13, 2008 | 1997 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...