Diagnostic Test Code (DTC) P0013 is "Exhaust Cam Position (CMP) Actuator Solenoid Control Circuit"
Diagnostic Test Code (DTC) P0014 is "Exhaust Cam Position (CMP) System Performance"
DTC P0014 can be caused by several things that can affect your variable cam timing system performance including using the wrong viscosity engine oil. However, since you have the DTC P0013, it is pretty obvious that the problem is being caused by a circuit malfunction in the control solenoid circuit. It could be as simple as a loose connection at the solenoid electrical connector. It could be that the solenoid itself has an open circuit in its coil windings, or it could even be caused by squirrels or mice chewing on the wiring harnesses in your engine compartment. You must diagnose the circuit to find the cause. Fixing the control solenoid circuit will most likely make both of these codes go away.
SOURCE: diagnostic code P0014
Could be a faulty cam actuator solenoid valve. Have read elsewhere that this code could also come up due to low oil , or low oil pressure .
SOURCE: GEARBOX DIAGNOSTIC CODES FOR FORD MONDEO AUTO 2002
all eobd codes starting with p zero have standard meanings irespective of model or make
PO12 CODE CAMSHAFT POSITION (cmp) intake/front,bank 1 timing over ******
possible cause valve timing engine macanical fault cmp acutator
POO36 CODE HEATED OXGEN SENSOR HO2S)2BANK 1, HEATER
CAUSE FAULTY SENSOR WIREING SHORTING TO EARTH EC
PO59 HEATED OXGEN SENSOR (HO2S) BANK 2, HEATER RESISTANCE
WIREING HO2S
THESE FAULT CODES HAVE BEEN OBTAINED FROM AN AUTO DATA DISC
I HOPE THIS IS OF SOME HELP TRY CLEARING THE CODES AND SEE IF THEY RE APEAR
IF THEY DO THE SENSORS AND WIRING NEED CHECKING
13,625 views
Usually answered in minutes!
Changed out camshaft sensors still same code
2010 chevy hhr has sputtering problem.check engine light came on and went to autzone they said MASS AIR FLOW SENSOR SO I RELPACED IT AND IT STILL SPUTTERS. CAN SOMEONE HELP ME OUT WITH THA?
What was the code ? P0 what , can't help without it . No code tells you to just replace a part . Diagnostics (testing) for said code must be done . Your best bet would probably be to take it to a qualified repair shop.
DTC P0101: Mass Air Flow (MAF) Sensor Performance
DTC P1101: Intake Air Flow System Performance
Circuit Description
The intake flow rationality diagnostic provides the within-range rationality check for the mass air flow (MAF), manifold absolute pressure (MAP), and the throttle position (TP) sensors. This is an explicit model-based diagnostic containing 4 separate models for the intake system.
• The throttle model describes the flow through the throttle body and is used to estimate the MAF through the throttle body as a function of barometric pressure (BARO), TP, intake air temperature (IAT), and estimated MAP. The information from this model is displayed on the scan tool as the MAF Performance Test parameter.
• The first intake manifold model describes the intake manifold and is used to estimate MAP as a function of the MAF into the manifold from the throttle body and the MAF out of the manifold caused by engine pumping. The flow into the manifold from the throttle uses the MAF estimate calculated from the above throttle model. The information from this model is displayed on the scan tool as the MAP Performance Test 1 parameter.
• The second intake manifold model is identical to the first intake manifold model except that the MAF sensor measurement is used instead of the throttle model estimate for the throttle air input. The information from this model is displayed on the scan tool as the MAP Performance Test 2 parameter.
• The fourth model is created from the combination and additional calculations of the throttle model and the first intake manifold model. The information from this model is displayed on the scan tool as the TP Performance Test parameter.
The estimates of MAF and MAP obtained from this system of models and calculations are then compared to the actual measured values from the MAF, MAP, and the TP sensors and to each other to determine the appropriate DTC to fail. The following table illustrates the possible failure combinations and the resulting DTC or DTCs.
DTC P0102: Mass Air Flow (MAF) Sensor Circuit Low Frequency
DTC P0103: Mass Air Flow (MAF) Sensor Circuit High Frequency
Not one of these codes tell you to just replace the sensor
×