Question about 1996 Oldsmobile Eighty Eight

Open Question

How do you remove the ignition switch on a 1996 Oldsmobile Delta 88?

Key is broken off inside ignition which is on the steering column.

Posted by mmartin84 on

Ad

1 Related Answer

Anonymous

  • 432 Answers

SOURCE: Sloppy steering column on 1989 oldsmobile delta, steering column

Check the Rag Joint under the hood.

Posted on Nov 04, 2009


Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car wouldnt start ooutta nowhere,, would have to push key in harder b4 wouldnt start finally... help feel like i am paying too much san antionio tx


the first thing to do is to use penrating oil to lubricate the key barrel if the please replace the ignition swicth assemble,remove the steering column cover by a metal screw then remove the cover and remove the screw from the cylinder barrel remove the ignition swicth assemble then replace with a new one

Mar 17, 2011 | 1996 Oldsmobile 88

1 Answer

Key lock steering column


on this vehicle you will have to replace the ignition switch because the tumblers are worn and locking up that is why you can't unlock the steering column

Feb 12, 2011 | 1985 Oldsmobile Delta 88

1 Answer

Replace key ignition 1987 delta 88


That job requires a partial disassembly of the steering column, with some specialized tools, to access and remove the ignition cylinder hold-down bolt.

Sep 28, 2010 | 1987 Oldsmobile Delta 88

1 Answer

I have a 1994 oldsmobile 88 Royale with a 3.8 v6. I have asked this question to 2 "experts" and no one seems to be willing to answer this question: There is linkage that goes from the lock cylinder down...


The starter switch fails commonly. If the linkage does not move then it has probably broken loose from the ignition switch and switch will have to be replaced.
  • Disconnect battery ground cable . Remove the upper steering column shroud by removing the self-tapping screws. Remove four bolts retaining lower steering column shroud and remove lower steering column shroud.
  • Remove lock screw and disconnect the ignition switch electrical connector.
  • Rotate the ignition switch lock cylinder to the RUN position.
  • Remove the two screws retaining ignition switch .
  • Disengage the ignition switch from the actuator.

  • NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Jun 19, 2010 | Cars & Trucks

    1 Answer

    How do replace the power steering pump on 1996 oldsmobile delta 88


    remove the pressure and return line, the belt, remove the mounting bolts. Use a "power steering pulley puller" to remove the puller. This tool also works as an installer.

    Apr 16, 2010 | 1996 Oldsmobile 88

    2 Answers

    94 olds 88 want start


    yes it can be the security system, find the two all white wires at the bottom of the steering column and cut them and solder the correct ohm resistor in between you will need an ohm meter to measure the resistance of the chip on the ignition key then install that omh resistor to the wires.

    May 28, 2009 | 1994 Oldsmobile 88

    1 Answer

    Error codes 71&72 for old delta 88 royale


    take key to dealer and check resistance. if key is OK probably wire is broken in column from ignition or ign switch is bad

    Aug 11, 2008 | 1992 Oldsmobile 88

    Not finding what you are looking for?
    1996 Oldsmobile Eighty Eight Logo

    Related Topics:

    165 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Joe Taylor
    Joe Taylor

    Level 3 Expert

    2228 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14852 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...