Question about 1995 Plymouth Voyager

1 Answer

Took my back three distributor cap wires off. Put them back on and now why car won't crank?

Posted by Reggie Ppleasant on

  • 1 more comment 
  • Greg Bernett
    Greg Bernett Nov 28, 2011

    Sounds like you crossed your wires....what size of motor do you have, 2.2, 2.5, 2.6, 3.0, 3.3, 3.8L?

  • Reggie Ppleasant Nov 28, 2011

    3,0L

  • Reggie Ppleasant Nov 28, 2011

    Ok, thank you. I will try.

×

Ad

1 Answer

Greg Bernett

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 2,989 Answers

Follow this diagram and trace each wire to the correct plug:

Took my back three distributor cap wires off. Put  - 11_28_2011_3_18_47_pm.gif

Posted on Nov 28, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1975 toyota celica ta22 gt won't start


check your fuses and kick starter also check if there is a spark from the plug wire if there is no spark check your coil and the distributor i think the problem will be solve

Jan 20, 2013 | Toyota Celica Cars & Trucks

1 Answer

I have a 1988 ford F150 4.9L VIN code (Y) .I had a bad head gasket and a bad head so i replaced both of them. Now that everything is back together i can get the engine to crank but not fire over.


I would suggest that you have incorrectly timed the engine.The proper way is to set number one cylinder to top dead centre on the compression stroke, if you look at the harmonic balancer on the front of the engine you should see a groove that marked top dead centre.With the engine at set at top dead centre take the distributed out of its mounting.
with the cap removed, you should find a small market on the top face of the distributor body.
This might only be a small mark but it is on the flange where the cap normally sits.
When you insert the distributor the mark on that distributor casing should line up with the distributor rotor button. You may have to remove the distributor slightly so that you can line up the rotor a button.
You may in fact have to do this two or three times until you get the marks lined up.
Then check the firing order of your engine, this is normally marked somewhere on the engine.
Once you have done this you should find the engine will start, you may have to adjust the advance on the distrubor to 4 to 12 degrees before TDC with a timing light.
regards

Feb 18, 2012 | Cars & Trucks

1 Answer

I have a 94' gmc sierra 4x4 1500 z71 then it won't start after i touched the distributor cap actually i replaced it. the parts look the same so i thought it was the coil then i did bt still no...


If all you did was replace the distributor cap and now it won't start. Either the cap is the wrong one, or it is faulty, take it back to where you bought it and have it replaced for another one. Make sure it is the correct one for your model.
When you took the cap off, did you remove the rotor button also? If so did you remember to put it back, don't laugh it is a common mistake.
Something else to check is that all the plug wires are snug in the distributor cap. Test this by pushing down on the actual wires and not the caps. Some times they don't go in far enough.
A couple of other things to check in the cap is for 'tracking/arcing' you will see this by taking the cap off and looking inside it and if it is tracking you will see a what looks like a hairline crack, this is from the electrical charge arcing out.
Check the little carbon rod that sits in the top of the distributor cap make sure it springs in and out and isn't broken.

Aug 01, 2011 | 1994 GMC Sierra

1 Answer

I removed my distributor cap. And I put it back on. I tried starting car up. But it wont. I believe I accidently change timing. How do I put it back on right timing?


Unless you removed the three bolts that hold the distributor in, you would not have changed the timing. If you did remove the three bolts, then it is likely that you put the distributor in and did not line up the cam with the distributor shaft tangs and now either the distributor or the cam is broken. If you just removed the cap then you may have broken off the spring loaded graphite connectors that protrude between the cap and the coil, or the center electrode on the cap. If you removed the wires that attach to the cap, then you may have put them back on wrong and you will need a diagram or another car that shows you where they should go.

Jun 05, 2011 | 1997 Honda Civic

1 Answer

1982 camero z28, engine 305 , carburator, 2-barrel Have replaced rotor, distributor cap, spark plugs and wires, replaced the coil. Checked the pick up coil and capacitor and was good. The problem is I am...


Sounds like you don't have the ignition wire from the key hooked up.its one wire,with a female end that plugs into the distributor. One side is power,one side is tacometer send me a pic of the distributor ifor you can

Apr 06, 2017 | Chevrolet Camaro Cars & Trucks

5 Answers

Truck wont crank. we have put new distributor cap, rotor button, coil pack, plugs, wires, and fuel pump. we also checked our firing order.


you said you repl dist cap that means you don't have a crank sensor you have electronic ing module. remove your elec ing module have it tested most auto parts stores could test your module, or check your coil at the neg terminal. should have power. if not you lost your primary volt from your batt.your secondary power is coming from your electronic ing module from the module to the pos terminal on the coil, when the eng cranks,from the coil to the dist cap , from the dist cap center to the rotor then out to the plugs,this all happen pervided the timing belt or timing chain is ok. the cumbustion chainber needs 3 things , thats fuel, air, and spark.

Apr 17, 2011 | 1996 Chevrolet K1500

2 Answers

Took the distributor out and cleaned it then put it back in and now the truck wont crank but tries to do so. need some tips please


Did you take out the ENTIRE Distributor or just the cap?

If you took out the entire Distributor, and put it back in, there is a possibility that you put it in backwards. The bottom of the Distributor has a 'notch' in it. If you turn it 180 degrees the wrong way, and put it back in, your truck will not start, because it is in effect 180 degrees out of alignment with the timing.

If you only took out the cap, refer to your owners manual (Hanes is best) for the plug wire placement in reference to the firing order, and make sure all the plug wires are in the correct locations. Also, make sure your plug wires are seated all the way down onto the plugs, and the cap is secured tightly onto the base of the Distributor.

Make sure your Coil Wires are also seated properly to the coil and the Distributor.

Clean the battery connections. Remove the battery connections, clean them and reinstall.

Nov 16, 2010 | 1991 Toyota Pickup

3 Answers

Changed distributor cap now car will not crank


You should check to make sure that the rotor button is in place. Also check the coil wire and the fire orderr to make sure that no wires are crossed. These are pretty much the only reasons why your car won't crank with the distributor cap change.

Aug 05, 2010 | 1985 Oldsmobile Cutlass Supreme

1 Answer

91 honda accord wont crank


There is a sensor under the left hand side of the dash that would not allow it to start, provided that you have replaced the electronic spark module inside the distributor first, which is what it sounds like it would be, When you say you replaced the distributor I assume you replaced it complete!

Jun 12, 2010 | 1991 Honda Accord

Not finding what you are looking for?
1995 Plymouth Voyager Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...