2009 Hyundai accent in 5th gear the RPM is 4000 is this normal? My speed is 115 Klm an hour

https://www.youcanic.com/nissan-transmission-problems/

torque hyundai accent Questions & Answers - Fixya

www.fixya.com > Forum > Tags

Torque specifications for cylinder head 2000 hyundai accent Are you aware that ... cover gasket on my 1997 Hyundai Accent GLS (engine code G4EH, 1.3L).

Hyundai Alpha engine - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Hyundai_Alpha_engine

WikipediaG4EH in a 1999 Hyundai Accent L ... lb·ft (132 N·m) at 4000 rpm, although some websites quote the torque rating as being 97 lb·ft (132 N·m) at 2700 rpm. ... 1992 Hyundai S-Coup? LS specifications - Carfolio.com · 1992 Hyundai S-Coup? GT ...

[PDF]AERA Torque Specs

www.aera.org/uploads/4/3/7/7/43776611/aera-torquespecs.pdf
AERA Torque Specs. 500 Coventry Lane, Suite 180, Crystal Lake, IL 60014. Toll-free Technical Hotline: 1-888-324-2372 (1-88-TECH-AERA). 815-526-7600 fax ...

.

Torque Specifications - AutoZone

www.autozone.com/.../Hyundai.../Specifications/Torque-Speci...

AutoZoneTorque Specifications. Print. Specific to: Hyundai ... Specific to: Hyundai Accent2006. Hyundai Azera 2006. Hyundai Elantra 2006. Hyundai Sonata 2006.

Club Accent Qu?bec • Consulter le sujet - hyundai motor s

2,500 to 3,000 on a 12 yr old car. Newer vehicles with 6-9 speed auto transmissions sometimes run as low as 2,200. But your gearing is your gearing. Can't change that now.

Your synchronization rings are worn out. These rings and responsible for bringing the lay shaft and drive shaft to the same speed so gears can mash easily.

and 4000RPM at 90MPH is a problem??

Go to www.hmaservice.com and register your vehicle by VIN #..
you'll then have access to wiring diagrams, shop manuals,
service bulletins, illustrations, etc. To diagnose a 2000 or 2001 1.5L Accent Diagnostic Trouble Code (DTC) P1128 (FUEL SYSTEM LEAN -- PART LOAD), check the following:

• Check the intake system for air leaks.
• Check that the Mass Air Flow (MAF) Sensor (P/N 28164-22610) operation meets the specifications listed below. If the MAF sensor output is significantly lower than the reference value (10% or more), then replace the MAF sensor.

Table 1: Using the Hi-Scan Pro in the Hyundai Diagnostic Menus Current Data Screen TPS (%) 0
3.5
5.1
7.4
MAF (kg/h) 10
21
30
47
RPM IDLE
2000
3000
4000
Table 2: Using the Hi-Scan Pro in the OBD-II Menus Current Data Screen TPS (%) 0
3.5
5.1
7.4
MAF (g/h) 2.8
6
8.5
12.7
RPM IDLE
2000
3000
4000

WITH MANUAL TRANSMISSION

Table 3: Using the Hi-Scan Pro in the Hyundai Diagnostic Menus Current Data Screen TPS (%) 0
2.4
3.9
5.9
MAF (kg/h) 9.5
19.4
28.8
43
RPM IDLE
2000
3000
4000
Table 4: Using the Hi-Scan Pro in the OBD-II Menus Current Data Screen TPS (%) 0
2.4
3.9
5.9
MAF (g/h) 2.5
5.5
8
12
RPM IDLE
2000
3000
4000

any "adjustments" you carry out to reduce engine speed at any given road speed will affect the speedo/odometer reading,BUT,the simplest/cheapest way of reducing revs is to fit bigger wheels/ tyres.say fit 15" instead of 13"with the same profile tyres.this will reduce your revs by about 500 @75mph.but the speedo will read 70mph.also acceleration times will be considerably reduced.and put an extra strain on the clutch/engine.
alternatively,swop the whole drivetrain to diesel,75mph=3500.

You should have another gear "5th" at 70mph your tacho should read about 2500 rpm.
Make sure you don't need to depress something or push the gear stick against a spring to select 5th.
Is there a gear layout on top of the gearstick knob, do you have 5th gear on there?
The highest gear ratio is a little over 1 to 1 so at 70 mph you would expect 3500 rpm, but, it is a little over 1 to 1 so it will be closer to 2500rpm.

Hi,your car may have a bad tranny mount,if not souds like bad gear , (internal)

with driving with the check engine light flashing u may have done damage too the catiltic converter check that when u reve the engine there is alot of exhaust flow it should push your hand from the tail pipe (be carefull exhaust will be hot)
It would be helpful if u could list the codes you can buy a code reader from any automotive parts store relitvly cheap