Question about Mitsubishi Montero Sport
You can use a hammer against the ratchet to get it tight. smack it a few good times. First I would take it out and apply some loctite to it. Use the non permanent type.
Posted on Aug 30, 2011
Tips for a great answer:
May 06, 2011 | 2001 Cadillac DeVille
Feb 06, 2011 | 2000 Alfa Romeo 156
Jan 17, 2011 | 1999 Chevrolet Metro
Dec 09, 2010 | 1995 Saturn Sl
Place a drain pan under the radiator and drain the coolant from the radiator.
Squeeze the spring clamp holding the upper radiator hose to the radiator fitting with a pair of rib joint pliers and slide the clamp towards the engine.
Twist and pull the upper radiator hose off the radiator.
Remove the fan blade using a ratchet, ratchet extension and socket.
Rotate the belt tensioner pulley using a breaker bar and remove the drive belt.
Detach the water pump pulley using a ratchet, ratchet extension and socket.
Pry off the access plug from the upper part of the timing belt cover using a small standard screwdriver.
Set the transmission to Neutral and apply the Parking brakes.
Rotate the crankshaft pulley with a ratchet, ratchet extension and socket to align the "O" mark on the crankshaft pulley and the "O" mark on the belt cover.
Look through the cover access hole. If you see another timing mark on the camshaft sprocket aligned with the mark on the inner belt cover, cylinder number 1 is at Top Dead Center (TDC). If not, rotate the crankshaft one complete turn again and check for the alignment marks.
Unscrew the four mounting bolts and the Phillips screw next to the access plug from the timing belt cover using a ratchet, ratchet extension and socket and Phillips screwdriver.
Detach the crankshaft pulley using a ratchet, ratchet extension and socket and remove the belt guide (large washer) from behind the crankshaft pulley. You may need a pulley remover to take the crankshaft pulley off. If so, you can rent one from most auto parts stores.
Loosen the adjusting bolt on the tensioner pulley assembly using a ratchet, ratchet extension and socket.
Rotate the tension spring rollpin (this is the screw next to the adjuster bolt on the tensioner pulley assembly) away from the timing belt using timing belt tensioner wrench number T74P-6254-A. As you hold the timing belt loose, tighten the assembly adjuster bolt to lock the tensioner using the ratchet, ratchet extension and socket. Now remove the tensioner wrench.
Remove the timing belt.
Install the new timing belt starting at the crankshaft sprocket. Route the belt in a counterclockwise direction over the auxiliary and camshaft sprockets. Properly engage the belt lugs on the sprockets' teeth and keep any slack on the belt to the right side, between the crankshaft and camshaft sprockets. Make sure not to rotate any of the sprockets as you install the timing belt.
Loosen the adjuster bolt on the tensioner pulley assembly so the tensioner rolls against the belt. If necessary, push the tensioner pulley against the belt with a large standard screwdriver to remove any remaining slack on the belt.
Make sure the transmission is in the Neutral position and the Parking brakes are engaged.
Rotate the crankshaft two complete revolutions so that cylinder No.1 is back in TDC. This will help to tighten the timing belt on the sprockets.
Tighten the adjuster bolt on the tensioner pulley assembly between 14- and 21-foot lbs. (19.0 to 29.0 Nm) using a torque wrench.
Tighten the tension-spring bolt between 28- and 40-foot lbs. (38.0-54.0 Nm) using the torque wrench.
Install the belt guide (large washer) and the crankshaft pulley. Tighten the pulley bolt with the ratchet, ratchet extension and socket.
Install the timing belt cover with a new gasket using the ratchet, ratchet extension and socket and Phillips screwdriver.
Reinstall the water pump pulley, drive belt, fan blade and upper radiator hose.
Refill the cooling system with coolant.
Oct 11, 2010 | Ford Ranger Cars & Trucks
Jan 30, 2010 | 1991 Toyota Previa
Sep 22, 2009 | BMW 318 Cars & Trucks
Jul 16, 2009 | 1993 Ford Ranger SuperCab
Jan 08, 2009 | 1997 Nissan Pathfinder
Sep 26, 2008 | 1990 Nissan 300ZX
28 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: