Question about 2000 Volkswagen Jetta TDI

1 Answer

Master power window switch for 2000 Jetta 1.6 Comfortline

I want to fit above mentioned switch on another car.Please help me with the wiring which are as follow:

Pins Colour Connect to?
2 Yellow ?????
3 White/grey ?????
4 White/purple ?????
5 White/green ?????
6 White/red ?????
11 Brown/blue ??????
12 Grey/blue ??????
14 White/black ???????

Posted by deklerkj on

Ad

1 Answer

Marty Kay

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 44 Answers

Here is the wiring diagram.
Master power window switch for 2000 Jetta 1.6 Comf - image1-rjd215ca4bjns5jlakhqqumy-1-0.jpg

Posted on Dec 10, 2017

Ad

3 Related Answers

Jean Leblanc

  • 151 Answers

SOURCE: Fitting a new car stereo to the old wiring

hmm, this is an old post, do u still need help??
If u do lemme know and i'll give u a few tricks u can use.

Posted on Nov 17, 2008

Ad

Anonymous

  • 73 Answers

SOURCE: Stereo Wiring 1984 VW Rabbit

red brown is speaker(rear left),grey blue is remote for anntena.Hmm,red black possible is a amp or a live one(+12V)

Posted on Jan 04, 2010

Geoff Walton

  • 819 Answers

SOURCE: I have a 2000 VW GTI VR6.I'm trying to connect a performince chip

do not cut into these wires. any real performance programmer will not require you to do this. these ones that tell you to cut into the IAT will ruin a $700 mass air flow meter, and do not do anything. all they do is try to trick the computer into thinking it is colder then it actually is, and to richen the fuel mixture, which will actually HURT performance and emissions because the air density does not match what the temp sensor is reading. the temp sensor is there for a reason!

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power windows not working power to master switch


Make sure the Master Lockout button isn't ON.
There will be a different power source for Windows and Locks
You will still need to start by checking the fuse
Your Owner's Manual should have a decent description of location of that fuse.
Also keep in mind that a 2000 is 15 years old and lots can happen.
See if: 1. Door open or closed - and which door - makes a difference (that may indicate a damaged wire in door harness - Jam area)
2. Wiggle or hold down the "Window Lock" button to see if that is an issue (Master switch problem)
If all the windows don't work then start with the above - it is most likely associated with power or ground to the switch. You will probably have to physically remove the switch to check circuits at the switch connector.
Let me know what you find
Thanks

Feb 26, 2015 | 2000 Toyota 4Runner

1 Answer

My power windows not working


You might want to post this question in a different section. This is the computer section.

Jun 30, 2012 | 2000 Mitsubishi Galant 4dr Sdn ES

1 Answer

2000 Jetta nothing works in the driver door


look for a broken wire inside the boot between the door and body

May 08, 2012 | Volkswagen Jetta Cars & Trucks

1 Answer

2000 ford explorer master switch problem


Check for broken wires inside the rubber boot from the body to the driver door . Happens all; the time ,wires breaking . Also you should have check for B+ voltage at the master switch before replacing .
How To Diagnose your Power Window Problem Is the Switch or motor bad BUY...
The Trainer 24 Power Window Troubleshooting

Apr 29, 2017 | 2000 Ford Explorer

2 Answers

Windows will not roll up or down


THERE CAN BE SEVERAL DIFFERENT ISSUES THAT WILL CAUSE THIS PROBLEM. 1. DID THEY ALL STOP WORKING AT THE SAME TIME? 2.IF THEY DID, I WOULD CHECK FOR A BROKEN WIRES IN THE WIRE HARNESS BETWEEN THE DRIVERS DOOR AND FENDER AREA. YOU CAN SEE THIS HARNESS WHEN YOU OPEN THE DOOR. KEEP ONE FINGER ON THE WINDOW BUTTON GOING DOWN AND THE OTHER HAND ON THE WIRE HARNESS AND WIGGLE IT UP, DOWN, IN AND OUT. IF THE WINDOW MOVES THE HARNESS NEEDS TO BE REPAIRED. IF THAT DOESN'T WORK TRY- 3. DEFECTIVE MASTER WINDOW SWITCH. IF THAT DOESN'T WORK TRY- 4. ASK THE DEALER IF THIS CAR HAS A GEM OR BODY CONTROL MODULE THAT HAS TO BE RELEARNED.

Feb 25, 2011 | 2000 Jeep Grand Cherokee

2 Answers

I have 2000 VW Jetta 1.8 turbo, my car stumbles on acceleration, but run smooth at idle. I removed the air intake from the mass airflow sensor and the car died. Is the turbo bad or do I have another...


If you remove the mass air flow sensor then the car is getting to much air and the reason that it is dying is that the ECU is set for the engine to run with a specific air to fuel ratio, and if you have removed the breather element. or air filter then that can cause the slow or sluggish acceleration.

Jan 19, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

2000 Chevy Blazer Power windows work from drivers


Are you sure the side window lockout switch located on the drivers master switch isn't on? This will kill power to the other three switches.

If your sure its not on than the I would pull the left rear window switch. There will be two dark blue wires one of them should have power all the time. If neither have power than I would pull the drivers master switch and see if there is power at the dark green wires (one will only have power with the left rear window switch in the up position.

If those are good than check the dark blue wires. one will only have power with the drivers front window switch in the up position. the other should have power all the time. If there is power there than you have a broken wire somewhere. The first place I would look is in the rubber boot in between the drivers door and the body of the vehicle.

If there is no power that the switch is bad.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 14, 2010 | 2000 Chevrolet Blazer

2 Answers

Gear shift won't move out of park


safety switch on brake pedal. common cause is a wire breaking off. there are 1 to 2 wires going to this switch. It is located on the brake pedal bracket above the foot pad.

Jul 19, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

Vw golf 1.4 model 2000 comfortline. EPC warning light on if its brake light switch problem can you plz help me how to change brake switch.


on top of brake pedal there should be a switch. wire going on it, diconect plug turn and remove switch fit new one and reconnect plug

Mar 19, 2009 | 2002 Volkswagen Golf

Not finding what you are looking for?
2000 Volkswagen Jetta TDI Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...