Tip & How-To about Chevrolet Corvette

Helpful reminder

This may seem unnecessary, but it's something I've been doing and it helps me. Whenever I buy the first filter for a vehicle, I tear off the top of the box/package and write what it's for and then toss it into the glove compartment. Then on my next trip to W*L-M**T, I just carry it in with me. It keeps me from looking it up once in the store.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

1983 Buick Skylark keep stalling

Could be bad wires,dirty throttle body,or you can bring up by set screw at throttle,top or bottom.

May 01, 2013 | 1983 Buick Skylark

1 Answer

1999 Mitsubishi Mirage- Bogging down when flooring the accelerator?

Hi there,

Your vehicle incorporates an on-board diagnostic (OBD) computer, which monitors behaviour of your vehicle's engine and ommission related cicruits.

This sounds like an electrical issue (I suspect perhaps your Throttle Position Sensor - TPS, or similar circuit). Your OBD computer will have stored the appropriate code/s causing this condition.

Have your codes read by an approved Mitsubishi Agent, who will then be able to advise what will be required to fix this issue.

Having your codes read should ALWAYS be the first step, as this will save you $'s and time, elimination the need to purchase unnecessary parts.

Hope this helps,


PS: if this advice has helped you in any way, please rate this solution

Mar 19, 2013 | 1999 Mitsubishi Mirage

1 Answer

I just bought a 95 blazer yesterday and it seems to be stuck in 4 wd

have you checked if the vacuum actuator is working? this actuator would be found underneath your battery. you will have to take of the battery tray to get to the actuator. if you can find a way to connect the battery, once you've taken off the battery tray and start the vehicle to test the functions on the 4WD switch that would be very helpful. PLEASE BE VERY CAREFUL AND MAKE SURE THAT THERE IS NO WAY THE BATTERY WILL TOUCH THE FAN OR BELT WHEN DOING THIS!! Once you've engaged the 4HI or 4LO, the actuator should be sucked in. when you've set the 2HI, the actuator should be out, to the normal position. Also check to see if the vacuum line is good, most wear with time and tear in other places. hope this helped you. Is your 4WD switch blinking or does it stay on when you change the settings? NOTE that the pic shows the actuator in the normal (out) 2HI position. see pic below to see what the actuator looks like : azzkikronu_1.jpgazzkikronu_2.jpg

Aug 10, 2011 | 1995 Chevrolet Blazer

2 Answers

can not find the cabin filter on my 1994 Dodge Caravan--it is not under the glove compartment? van smells bad when air conditioner/heater is on- you suggested to clean the cabin filter but no one seems to know where it is???

I've had Caravans for many years and never had that problem however, if there is a cabin filter in the vehicle it is inside the air exchange box and you will have to open it to find the filter. Most likely in the top.

Jun 16, 2011 | 1994 Dodge Caravan

2 Answers


you have to buy a tool available at any auto parts store for about $15 its called a fuel line removal tool. then it just slides on the fuel line and into the coupling piece to push down the pins inside it to release the line

Mar 19, 2010 | 1997 Acura CL

Not finding what you are looking for?

1,826 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions