20 Most Recent 2013 Hyundai Accent SE Questions & Answers


its suppose to lock and unlock all doors latch may need lubricating or an electrical connection problem if still under warranty bring in an have checked

2013 Hyundai... | Answered on Sep 29, 2018


Pull stereo forward and get the last 4 numbers of serial number off the top of the unit. (It’s quiet easy)Add that number to 1212 and that number is the code. So if the last 4 numbers is 1234 +1234 the code is 2468. Push 1 till you get 2, 2 till you get 4 and so on. 5 is the enter button.
The small sticker is the serial number.
7_20_2018_11_46_19_am.jpeg

Hyundai Cars &... | Answered 2 days ago


As the coils are identical it doesn't matter what order they are in though it is important they are wired correctly - fortunately this is taken care of by the different lengths of connecting cable.

Matter of diverse interest; each coil is generally only half a coil as they operate in pairs, being wired in pairs and only needing a single trigger to produce sparks for two cylinders. This is the wasted spark principle that has been much used with small 2-cylinder engines for a long, long time.

What this means in practice - a misfire or similar spark problem with a cylinder could be caused by a fault with the other half, the paired coil.
It is best to replace the coils in pairs or at least check the other coil for shorted turns...

Hyundai Cars &... | Answered on Jun 22, 2020


First check the immobiliser is properly disarmed then check for a good spark.

If the immobiliser is OK and you have checked the spark, please repost for further advice.

Hyundai Cars &... | Answered on Jun 20, 2020


790 pages of service info which may provide some help on 98 Accent 1.5 below
https://automotrizenvideo.com/wp-content/uploads/2011/11/manual-de-despiece-hyundai-accent-98-1.5-SOHC.pdf
If you are looking for all equipment which has a connector to the ecu or ecm a wiring diagram would provide info as to where the ecm get info from and where it sends it to.

https://www.cargurus.com/Cars/Discussion-c2203_ds502664
Some general info in link below. Basics of video crank sensor keeps blowing fuse to ecm.
https://www.youtube.com/watch?v=ubkHu4gPbbc

Hyundai Cars &... | Answered on Jun 20, 2020


Throttle Position Sensor needs replacing. It tells the fuel management system how far down you have the accelerator pedal.

Hyundai Cars &... | Answered on Jun 14, 2020


Was it new or used. Possible a bad battery or connections. A lot of parts houses have a tester to test them.

Hyundai Cars &... | Answered on Jun 05, 2020


Could be from the hose, hose clamp , intake housing gasget .The parts store have radiator pressure testers with which you can put pressure in the system while it not running and then you can find out exactally where the leak is coming from.

Hyundai Cars &... | Answered on May 31, 2020


All cars are different even same model/makes depending on year could be different!
Check you vehicle handbook for details!

Hyundai Cars &... | Answered on May 30, 2020


Check the regulator is set at the correct voltage.

Hyundai Cars &... | Answered on May 29, 2020


https://www.youtube.com/watch?v=i2TVuBp-n0Y
Must be a common problem. Here is a video of where the emergency release is.

Hyundai Cars &... | Answered on May 28, 2020


This code is for the electronic throttle system. There might be other codes listed when you scanned the vehicle that might give you more clues as to exactly what is wrong. Comment with them and I'll try to help you further.

Hyundai Cars &... | Answered on May 28, 2020


This job will depend entirely on the actual engine you are working on and how much experience you have working on engines. Diesels are slightly different to gasoline as diesels need to be set up more accurately compared to gasoline. The best advice is that if you are in ANY doubt take the car to a Good Mechanic and pay them to do it.
To do this you will need to strip the Top half of the engine down. I would seriously recommend you buy a good quality workshop manual before you begin as that will help with the method needed and the torque settings you'll need for putting it back together.
You will need to drain the engine of oil and coolant, and the rocker cover for that side of the engine. Any timing belts/chains will need to be removed so you will need to set the engine to Top Dead Centre on cylinder 1 BEFORE you start and note the position of the timing marks used. You may also have to remove valve rockers depending on whether the engine is an 'overhead valve' or an 'overhead cam' type.
It is a lot of work but not difficult if you take your time doing it. It will take at least 1 full day to do. My first took 2 days.

Hyundai Cars &... | Answered on May 28, 2020


download manual:
https://www.manualslib.com/manual/834518/Hyundai-2001-Tiburon.html

Hyundai Cars &... | Answered on May 28, 2020


Yes this vehicle has one!

Hyundai Cars &... | Answered on May 28, 2020

Not finding what you are looking for?
2013 Hyundai Accent SE Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2004 Hyundai Santa Fe
2004 Hyundai Santa Fe

1,447 Questions

2001 Hyundai Elantra
2001 Hyundai Elantra

1,154 Questions

2000 Hyundai Accent
2000 Hyundai Accent

1,113 Questions

2006 Hyundai Sonata
2006 Hyundai Sonata

1,215 Questions

2001 Hyundai Accent
2001 Hyundai Accent

1,057 Questions

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hyundai Cars & Trucks

  • Hyundai Cars & Trucks

Most Popular Question

keyless entry operate hatch lock as

  • Cars & Trucks
Loading...