Top 20 2001 Toyota Echo - Page 3 Questions & Answers

odometer light inop , all other one ok

Hi, I came across this step by step explanation to remove it, along with photos. Good luck. http://gordosoft.com/echo/Toyota%20Echo%20radio%20replacement%20guide.pdf Mike

Are you saying you have spark and normal fuel pressure when cranking the engine ?

Under the steering wheel

new plugs air filter clean your throttle body fuel filter is inside tank so you don't have to replace the fuel filter good luck

I could suggest replacing the coil pack while your in there replace the spark plugs( as preventative maintenance) any check engine light? usually that's an indication of a misfire

DTC P1315 is Igniter Circuit Malfunction (No.2). Check No. 2 ignition coil.See the link below for more information from a 2000 to 2002 Toyota Echo Service Manual.Diagnostics: Engine: P1300, P1305, P1310, P1315 Igniter Circuit Malfunction (Echo)Hope that helps.

Check your engine mounts. It's an easy check. With the hood up, have a friend jump in the car and crank the engine. Look for the engine to "shake" or "jump" when he shifts the vehicle from park to reverse and back to park again.

have it serviced & check compression

You can use Toyota it2 to check the troubleshooting.

map censer i had that problem on oldsmob it is located on the thoutlebody

Turn off the a/c & see if it still does itTry dragging the brake while still on the gas to turn offtorque converter lock-up & see if changesCheck front drive axle CV Joints.Check motor & trans axle mounts

It is not that Hard, you can use the Jack from your Car... Lift up a little on the Oil Pan with the Jack, you will see the engine Mount move. Once you have that pressure on, then you just take the center bolt and then the mount bolts. Install the new Mount and lower the jack. YOU DO NOT WANT TO LIFT THE CAR, JUST GET WEIGHT OFF THE MOUNT

what oil use for power stering oil for toyota platz red or white

Spark plugs are replaced when the electrodes are found to be corroded, burnt, cracked or oil fouled. Normal spark plugs need to be replaced every subsequent 30,000 Km. Iridium - tip spark plugs are replaced every 80,000 Km.

on many cars there is a switch which turns off the overdrive; if you have one maybe you hit it accidentally. the other reason for this indicator is if the transmission has overheated; the computer doesn't allow overdrive until the trans. cools down

fuse or bad body ground check all ground's on the car

El relay de tu auto esta situado en la caja negra de fusibles la lado de la bateria enfrente, es una azul en la esquina superior. Es el mismo que yo andaba buscando suerte.

under the rear of the vehicle under the trunk

Adding key. Note: You must be having one working master key to perform this function. 1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked. 2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out. 3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out. 4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote. 7. Open drivers door.