20 Most Recent 2007 Toyota Sienna Questions & Answers


Hi

i have a Toyota Avanza 1.5 sx. been driving it since 2007 without problems

early this year the reve started mulfunctioning. it goes up and down in an idle mode. when it started it was cutting power as i stop.
took it to Toyota dealer 3x they could not identify the problem. its now better and like in the morn8ing when i start it it goes to 3000 revers and after a while drops down to 1000rerves. this problem is still happening like once in two days or once everyday of idling up and down

please help

2007 Toyota... | Answered on Sep 09, 2020


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

2007 Toyota... | Answered on Nov 01, 2019


A diagnostic scanner is best here, someone may have the exact answer but it'll be Luck 99/100 if you get the correct answer.This ic commonfkrbon board or factory installed anti-theft or security systems.

A few quick questions:
1.) Have you changed or disconnected the battery for any reason?
2.) Have you had any issues with the vehicle "turning off" or just "dying" in the road randomly while e ererythibg else seems Well ?

+If you have more than one key please try it, try both keys each way?
+Also unhook your negative [(-) or (black)] battery cable and learn it disconnected for about 25-30 minutes just to be safe.
+It may be time for a battery, get yours checked at any local autobparts store, have alternator, starter, & ODD2 System Cecked while you're they're- it's all free & may take 10 extra minutes. Trust me, do it!!!

if my answer has been helpful please met me know by clicking the green satisfied" button to let me know I'm doing my job. A 7-8 Word Review or Reccomnandatiom would be the best compliment I could ever receive. Thanks and have a Blessed Day, Good Luck!

4c919d4d-cf88-439f-8d18-c72c3e0329a7-b2iappo0szer0y03n3l01yua-5-0.jpeg

9bc815db-a296-47d5-b9c3-8a17dcd2c513-b2iappo0szer0y03n3l01yua-5-2.jpeg

fea0fa0a-bb72-4551-b32b-7c87b885c72d-b2iappo0szer0y03n3l01yua-5-5.jpeg

2007 Toyota... | Answered on Jan 28, 2019


Unfortunately you can't get these to go out until the issue causing them to come on is addressed. I'll trll you how to find out! You'll certainly need to check it out further(or have it checked further by someone who is a professional- that doesn't always mean someone doing it for a living in s garage either as I no longer do but did for many years and still do it all regarding my vehicles and equipment along with everyone's that I know. I didn't mean to get off track but that's something to think about, people like me will save you big bucks $$$, mechanically friends are useful. Thus "Professional" will need a diagnostic scanner, a good one, the parts stores can likely help with engine light, but a more specialized diagnostic scanner will probably be necessary for your second issue. This is likely to be found at a well Equipped local garage or repair shop, and of course the dealer will have this if no one else does.

Ask friends and family, co-workers, or whoever you trust if they know a professional technician and perhaps they'll know someone capable or at least have a few good suggestions. Look in the local business pages or online reviews for local shops, a Toyota or Imported Car Specialist would be a huge plus but not absolutely necessary.

If this helped you in any way please let me know by clicking the Green "Helpful" Icon as that's the best indication to me that I'm doing my part to be helpful. Leave a review or follow me as I answer auto, mechanical, & technical questions of all kinds. Thanks and have a Great Day!

2007 Toyota... | Answered on Jan 16, 2019


You most likely need to enter your radio security code. The original owner was given this code and instructions to use it when the car was delivered new. Otherwise see the dealer.

2007 Toyota... | Answered on Mar 18, 2018


You need to remove the bumper outer shell from the backing of crumple pad, but doubt that it will say popped out

2007 Toyota... | Answered on Feb 28, 2017


Visit this site ---> http://www.obd-codes.com/p0340

2007 Toyota... | Answered on Dec 28, 2016


change the emergency flasher

2007 Toyota... | Answered on Nov 08, 2016


Those codes are misfire need to change plugs r wire I need more info what kind of Vel then I can help u

2007 Toyota... | Answered on Sep 12, 2015


check for a failed strut bearing loading up the rubber mount as the thrust bearing is not turning freely and the spring is twisting up as you turn the wheel

2007 Toyota... | Answered on Mar 17, 2015

Not finding what you are looking for?
2007 Toyota Sienna Logo

283 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sienna Toyota

  • Sienna Toyota

Most Popular Question

pop out big dent in plastic bumper 2007

  • Cars & Trucks
Loading...