20 Most Recent 1994 Jeep Cherokee Questions & Answers

I'll post all 3 and you can decide which style you have:

Pic 1---


1994 Jeep... | Answered on Oct 25, 2019

Find where the alarm is hooked into the electrical system Usually where the wires come out of the steering column from the ignition switch. They cut the main feed wire and hook up the alarm. Disconnect the alarm wires and re connect the oem wires. They will look alike

1994 Jeep... | Answered on Apr 19, 2019

could be your ignition switch is bad. it is old ya know

1994 Jeep... | Answered on Nov 28, 2017

Hope you can read it? If not I'll try something else. See the compressor relay, that line with arrowhead is load side of relay, when relay is energized that arrowhead moves to other terminal, that is a fuse protected circuit, goes hot with the key on, underhood fuse box/power distribution center f6--15amp. The left side of relay is control, needs voltage and ground. fuse f5--25 amp interior fuse box and is wired through selection switch. As you can see, the computer grounds control side of relay.
Your second paragraph sounds like a big voltage drop, somewhere, I'd have make sure battery is good and charged up, check battery connections and check your charging system.
hvac 1-v5mpaghvzo1rjsiaaldzfraw-2-0.jpg

hvac 2-v5mpaghvzo1rjsiaaldzfraw-2-2.jpg

1994 Jeep... | Answered on Apr 24, 2017

bad wiring
get it fixed
we cant teach a year of school on topic in this box.
but can say if you had voltmeter
and used it , to find the Break point of current,
you'd already know what wrong.

google how to test automotive electrics, or buy a book?

1994 Jeep... | Answered on Mar 29, 2017

gauge stuck high or low or"??????????????
how to ?
with no tools or with ?
got meter? or nothing.?
is tank full now, empty?
knowing that we can check the sender.
using an OHM meter, dmm set to resistance
unplug sender and check its ohms to ground.
infinity reading is bad sender
btw at 63ohms the sensor is at, cause the low fuel lamp to glow.
page 8e-6 in the factory manuals shows doing all this.
its in every jeep book in print. XJ jeep.
8e-23 shows.
empty tank is 105 ohms
1/2 full is 33 ohms
and full is 5 ohms.

first is fuse good to cluster, do all other guages work?
then unplug C203, below near tank
see that wire,DB, (dark-blue)
measure it to with ohm meter, must read 5 to 105 ohms
if not and is why too too high .
unplug C307, and measure black to VT, (violet?)
100 to 5 homes if ok now, the ground wire there is rusty.
if not ok, the sensor is toasted.
if all this check ok.
then at c203, DB wire ground that wire,
and gauge must go to fULL key on,
if not . the DB wire is bad, or custer guage, bad,
if this test fails we do this same grounding test
at the actual gauge. if fails, gauge is bad.


1994 Jeep... | Answered on Nov 03, 2016

Hello Robin Williams,

Your phrase "Go into gear"...
(comment me back if I got it WRONG... I can change )

MANUAL Transmission I presume (4 or 6 cylinder)

IF you can work it thru the gears... while the engine is OFF... it is the clutch... (otherwise a major malfunction of shift levers/forks)...

A sudden failure of the clutch would MOST PROBABLY be the linkage:

I sincerely believe you have hydraulic cylinders check fluid level, hose etc. (any wet spot is you exact problem area)

Most costly parts are the Rock Auto Master... $24 to $50 and the
$lave cylinder... $18 to $70 (interesting)

(personal opinion... if one goes bad the other will soon follow).

Hope this helps.

Be safe... work safe!

Rock Auto Parts Catalog

1994 Jeep... | Answered on Jan 29, 2016

which engine.?
the XJ has a serp, in the USA LHD. (left hand drive)
most have no auto tensioner (sorry !) its not a GC.
the 4.0L has a screw drive, tensioner, not like on new cars.
the force is below. why not just buy a new one... start fresh.????.
if the screw, below the PS, that huge long screw was never set right then it will slip, most shops are to lazy to do it right
or too cheap to own the simple tool to measure tension.
as you can see its NON TRIVial AT 180 LBS.
FROM THE XJ BOOK, ,valid to 2001. RHD never LHD cars.
and never export cars. 4.0L only., so.....


posted the free book on xj 200 times
the chapter 7 covers all this,
if you care to read. RTM?


LHD ONLY !!!!!!
24715298-hkt52gi400f4we1nv5hxgewe-2-3.jpg the force spec. is HUGE.
that is the first thing go learn on 4L back then.
same my 2 1988s, xj and pickup twins. 5million made.

1994 Jeep... | Answered on Jan 01, 2016

your anti theft is activated,you need the original key and keyfob to start it,if you dont have them,all you can do is call a jeep dealer.

1994 Jeep... | Answered on Apr 26, 2015

Antenna good not broken

1994 Jeep... | Answered on Apr 04, 2015

No cranks is here
the starter just CRANK.
IF lucky so does the crank shaft turn.
then the engine starts and runs, (this is not turns)
it's running
the EFI then sustains running , if ABS stays happy.
the engine can also stall.

1994 Jeep... | Answered on Mar 14, 2015

wow no symptoms. no sound sure, but in a/m f./m , cassette, or CD and or USB port (MP3) are all dead too>? and is the dial dead TOO>? 100% dead, is that it? ill assume !00%
factory radio have password codes , never aftermarket radios.
ask kenwood, the answer is NO !
your operators guide (jeep) is useless for swapped in radios.

how?, is super easy and 10x on a bench.
no matter.
there is but one 1 wire for power, (on all aftermarket radios) this is a standard, RED wire, must have 12vdc, (ever use a simple voltmeter)?
if radio case and black wire is grounded. are they'
if yes the radio is DOA.

some DOA radios (10000s of models made in 40 years)
have fuses inside or in back of radio, look on back first.
if you seen nothing there, it got none.
open lid, see fuses inside,?
reitred ET i am, DC to day light experience.

1994 Jeep... | Answered on Mar 08, 2015


1994 Jeep... | Answered on Dec 08, 2014

You are still getting high or low voltage at tps? What is the voltage and do you have a unstable idle? Put you + lead on terminal 3 and - lead on terminal 1 turn ignition on and check voltage to be at approximately 5 volts. You can also back probe with it connected at center wire and ground probe to a good ground at engine. Turn ignition on it should read between 0.20 - 0.90 slowly manually open throttle it should rise all the way to 4.5 voltd at full open. If its bad change tps if no 5.0 volts from pcm on first test check connections at pcm. The center tps connector supply wire comes from pin 22 and connection 3 ( which is 5 volt supply ) comes from pin 6. You should be able to back probe pin 6 turn ignition on and have 5 volts. If not 5 v brain has problem.

1994 Jeep... | Answered on Sep 08, 2014

If you need to ask, you not upto it

1994 Jeep... | Answered on Jul 29, 2014

Not finding what you are looking for?
Cars & Trucks Logo

257 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 Jeep Cherokee
1998 Jeep Cherokee

1,365 Questions

1999 Jeep Cherokee
1999 Jeep Cherokee

1,143 Questions

1995 Jeep Cherokee
1995 Jeep Cherokee

687 Questions

2000 Jeep Cherokee
2000 Jeep Cherokee

657 Questions

2001 Jeep Cherokee
2001 Jeep Cherokee

643 Questions

Top Jeep Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Cherokee Jeep

  • Cherokee Jeep

Most Popular Question

2000 jeep cherokee sport serpentine belt

  • Cars & Trucks