2004 Lotus Esprit - Answered Questions & Fixed issues

have to be quick ,got to get er indoors from work,or an earbashing .right back to car talk --not exactly sure what iam dealing with here ,carb or injection ,it has a distributor if its an 86 but does it have points or a module inside the distributor or just a pick up with the module under the coil ,Also this turbo ?? someone put new bearings in?? or the rotors as well .must dash i have 5 mins to go and get the old dragon

HI, sorry I am not closer, but the mechanics are very easy for any good mechanic, if you get a workshop manual from a UK Lotus specialist (sjsportscars). they do all parts mailorder the manual is very detailed, if you have a standard model, if you have the US high spec most race shops can tune the engine

you meant does not crank, (starting is next after cranking it first) the gear shift works in park or neutral , you operator guide states that. yes that means the PRNDL switch in or on the gear box is bad. or wires to it corroded pins or damaged, also called range switch. or TRS , tranny range switch, easy no? you found the hard proof and told it. when bad switch or bad wires to it.

https://www.manualslib.com/ Your owners manual should show you how to reset it.

it is in and or under the back seat. put it toward the middle of the car. if not you will brake it and the truck will not close. So you might want to go to the dealer to find out if there is a fix now to get the cable replaced so if you try to open it the wrong way at least you can close the trunk

Lotus Esprit Wikipedia

You just go to the link I attached I'm sure you will get the solution of your problem lotus elise

There is a manual trunk release that is inside the car near the rear seats. You must make sure to pull the release towards the tunnel/middle of the car, not out away from it. Apparently, a number of sales people have tried to demonstrate it and by pulling on it incorrectly, broke the inner workings leaving the trunk then incapable of latching closed. The repair is not simple. Something about the cable being encased in a tube that is not straight but curved, so that when you pull on it the wrong way, it breaks something. Lotus is redesigning that component. Also note you may need someone to gently lift on the trunk as you pull the lever. It should be a yellow lever.

The usual culprits are bad ignition relay, bad module or coil(s). Ignition switch also possible.

sounds like the coil packs , get the OBD codes read to confirm

Normal operating temp for any car is 150-170 F, Your thermostat is set for these amounts, water boils at 220 F and coolant boils at 260 F, but the boiling of anything in there is not good, it creates pressure, something is going to give. Your radiator cap has a temp on it too, about 165. It will bleed off the pressure before it explodes. So, you can check your thermostat, they do freeze up, check your coolant, don't run straight water. and then check the inside of your radiator, they do clog up. Hope this helps.

You give absolutely no clue what on!! All questions in Cars and Trucks category need full 'year make model'. If it isn't a Car it needs 'make model (what it is)'.. All the above should be the first 3 words in all questions. Then you have over 40,000 categories to choose from. We can't guess from what you have written. ..

If the belt has fallen off there must be a problem. The don't just fall off of the car without assistance. With the belt off, check all of your pulleys to make sure they are turning properly. Then, get the manual for your vehicle and it will show you how to do this job :() Every car is different but all cars are the same generally and this is usually just a matter of putting the correct wrench into the tensioner to remove/apply tension and route the belt around everything in the proper direction. There is usually a sticker in the engine compartment/hood area that shows the diagram of how the belt is routed.

Question edited for a lot more clarity.

Hino J08 engine specs, bolt torques

Barrington Diesel Club https://barringtondieselclub.co.za > hino > hino-j08 Hino J08E, J08C specs and bolt torques with links to manuals ... Hino J08E Connecting Rod Bolts Step1 = 51 lb.ft ... main bearing cap bolts, connecting rod cap ...

Workshop Manual Hino J08C No.1 ' PDF

Scribd https://www.scribd.com > document > WORKSHOP-MA... ... SPECIFICATIONS DIESEL ENGINE FOR INDUSTRIAL USE HINO) §=JO8C-T eannzn. ... bearing cap bolt are tightened to the specified torque. ... Connecting rod bearing 16. "); background-repeat: repeat-x; display: inline-block; overflow: hidden; position: relative; background-size: 14px 11.4px; height: 11.4px; width: 68px;"> "); background-repeat: repeat-x; display: block; background-size: 14px 11.4px; height: 11.4px; width: calc(62px);"> Rating: 4.6 · ‎ 10 votes

Hino J08C Engine Torque Specs

JustAnswer https://www.justanswer.com > Truck Repair Sep 29, 2012 - Hi I'm Wayne I will help you with this. Good Morning Rod Bearings 51 FT/LBS + 90° + 45° Main Bearings 196-209 FT/LBS Head Bolts Missing: connecting ‎' Show results with: connecting

HINO DIESEL ENGINE WORKSHOP MANUAL

jimcontent.com https://s4b621f162e87bd31.jimcontent.com > name PDF Cylinder head bolt, crankshaft main bearing cap bolt, connecting rod bearing cap bolt, etc. ! CAUTION. • Measure the overall length of the bolt before. ..

Head bolts

Best Manuals to fix your car go to http://www.reliable-store.com/

Make and odel unknown but it suffices to say, the ignition key is coupled to the anti theft device and may need programming.

Hi,engine z6 mazda 3 2007 main bearings torque?? please

Dodge use a system called a "Lost Spark Ignition". Basically each coil fires two spark plugs on two different cylinders at the same time every time. One firing for the ignition stroke and the during the exhaust stroke on the other cylinder. Simply, a spark fired every other stroke on every cylinder. That means it only needs 3 coil packs on a V6 engine. Your firing Order is 1, 2, 3, 4, 5, 6. Cylinder numbers are set as Odds and Evens. Stand with the belts and pulleys nearest to you. The cylinders on the Left side are the Odd numbers and the cylinders on the Right side are the Even Numbers. The cylinder on the LEFT side nearest to you is number 1. The middle one is number 3 and the one furthest away is number 5. The cylinder on the RIGHT side nearest to you is number 2. The middle one is number 4 and the one furthest away is number 6.

If you find screws or a latching mechanism, use the appropriate tool to open the compartment. It might be a good idea to wear gloves during this process to avoid any injury from broken glass and make sure the replacement bulb is the correct type for your scale.