20 Most Recent 2004 Hyundai Tiburon - Page 7 Questions & Answers

There are 6 screws (3 outside, 3 inside), and pull the glove box strongly,there are come clips that require a good pull. Be careful of the light in the box. For more help and proper diagrams please click on the link below:--- http://forum.crookedh.com/showthread.php?t=4030 -------------- Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Takes 134a freon, same for sealer.

look under your dashboard there is a written for the name what fuse for

yes

Hi There,

You will find the second fuse box on the right hand side of the steering wheel (australian - left hand side if in america) located underneath the power "mirrors" button. Follow the side power "mirrors" button down until you reach a false wall, unfasten this. another word for this is the "fascia"

Hope this helps

Cheers Buckaroo,
Chris

Hello There,

When you bought the car and the dealer sent it for rust proofing etc, they would have put the cables which connect the power windows to the fuse box back together loosely, this is a usual occurrence and a tricky way to get you back and have this and that changed and put you out of pocket. all you need to do is have a trusted mechanic take the inside part of the door off. It unclicks quite easily. and have them reconnect the cables properly. You should never have a problem with your window again.

Cheers Buckaroo,
Chris.

hi this could be a couple of thing, but sounds more like the heater relay is u/s, this is the one that heats the glow plugs before starting, check fuse box and see if fuse has blown first, but normally it would be the relay, the other thing could be a bad earth to the engine, check the earthing straps around the engine area, as one could be broken, also check the earth wire connection the heater rail to the plugs ( its the one that runs down the glow plugs and looks like a copper strip or similar ) check to see if is loose or broken...hope this helps please vote thanks

i have the same problem let me know if you figure it out... it is starting to drive me crazy

reset alarm system.as a first step....with remotes.

Sounds like your alternator is bad, if car will stay running long enough to get over to an auto parts place where they can do an alternator test for free have it check or you can remove alternator and take it to them so they can test it. or with a volt meter start car remove jumper cables and check voltage at battery, should have no less then 13.5 volts, what your checking is alternator output voltage.

The first thing that I would do is go to Hyundai website and see if they offer the wiring diagrams for it. They are a co company to KIA and KIA does show all the overhaul infor on their cars for free. If they don't, you can go to www.autozone.com and input your car information and look up the wiring diagram that way.
What you are looking at:
1. Bad bulbs in the housings, check them all and remove and reseat.
2. Shorts in the wiring to the housing
3. Shorts in the steering column
4. Bad turn switch or ignition switch
5. Short in the fuse blocks.

Hi! You will need to replace the TURN SIGNAL SWITCH also known as FLASHER RELAY. Two things happen when this is faulty, either wont flash or will flash continuously even without activation. Have it replaced and you'll be good. Hope this helps and have a good one!

check battery should be available at any radio shack store most of them will check it for you. also look for corrosion from moisture as they are always subjected to this outside

The fuel filter located on top of fuel tank beside the fuel pump. Accessible by removing the rear seat and detaching the inspection panel of the fuel pump.

Hope this can help.

Have you changed your fuel filter yet? If not do so. Also if this doesn't help then you may need a new idle sensor. Good luck!

follow the red battery cable.That cable goes right to it.

you might have blown the fuse go to your fusebox on your car and check to make sure each fuse is still good replace all the bad fuses(if any) and then it should work

if you do not want to spend the money to buy a haynes/ chilton manual, then you can call the parts store and ask them for the firing order, they should tell you over the phone.. they have done that for me many times.... hope this helps.....

replace the whole turn signal .