Top 20 2000 Jaguar Vanden Plas Questions & Answers

This is common if your throttle is electronically controlled and not cable controlled like (older cars). If the throttle body main butterfly sticks for a fraction of a second because it's cold and the throat is full of carbon, for safety the computer will kick it into that mode. This can also happen if the throttle sender unit on top of your throttle peddle is faulty ... or kicked and the plug is not all the way in. A simple code reader can reset the issue but if it happens again start by cleaning the throttle body.

give the interior door panel a couple of heavy thumps with your hand it may work again for a while the normal prob is caused by sticking/worn out motor brushes the shock releases them and the motor works again. if so then that confirms the motor needs changing. if not check the wiring/connectors to the motor, but the motor is most likely the cause. hope this helps.

Check the owner's manual.

Hi there I am a tech mechanic and I tell you what do a voltage drop test nev to nev n po to po I bet you have a broken a current test Evey thing until you find the drop n then look up wire diagram and see the conn. N also have you check out the hot feed to the power dist. Box with test light and di. Volt meter reader I no that you have a volt drop on that circuit and make sure you are testing volt drop before during and after you have to test everything you worked on I can tell to its electric problem with the car also you check the cam n crank sin. For a 5 volt signal to start! And the rely box you also have a battery saver rely too and what bout the ignition switch n lock n key just bc things come on don't make the switch good that pin rod could not be able to make conn to close the open switch to start the car and you also have fuse line links for your starting system they are like the box it go nut works! One more thing to is it a no start problem or a no crank their is a difference between them! Check out the cable coming out the bottom of the colo and the colo its self if the wheel locking pin hung up or broke it wont start but here is my email address I like to no what you come with with and if you need more help [email protected]
BTW make sure its not locked up or VAp locked check out wire diagrams make sure you don't have fuel kill switch to

Why won't key work in door? Most likely not used? Spray wd-40 in door lock and insert key moving it back and forth in a sawing motion. This will usually free up a sticky lock and you can then turn it. Most lock out companies use a long metal rod. They will pry back the top of the door where it meets the roof and insert a wedge to hold the door slightly ajar and then insert the rod which has a hook to catch the lock and unlock it. A coat hanger unfolded will usually do the trick with a little patience. If not, the only other way is to disassemble the inner door panel ( usually causing damage ) to get the door open

sounds like the latch actuator has failed, i dont think it has a seperate fuse for each door, you could check that you havent got a broken wire in the door wiring around the door hinge area. the actuator is part of the latch, but you may be able to get just the actuator which is easy swap over, check the wiring first, you could use a test lamp or circuit tester on the connector to the actuator to see if it being powered up when you press the plip. latch the door shut before testing, good luck.

You don't say what model but the locks are not fused separately if the others are working it might be the latch

You have a fault with ASC you need to get the fault code.

Depends in the mileage since the transmission was last serviced. It sounds like low pressure from the pump. It could be just a filter. You did not say where the leaking seal is, but a leaking seal will not fix itself.

if its a v8 its on the underside on the flywheel/torqueconverter housing in the centre 8mm bolt or torx head close to the subrame crossmember if its a x300 straight six its on the top front above crank pulley 8mm bolt.

There are generally 2 power wires on a stereo. One is tied into something that only comes on when the ignition is turned on and the other must be live at all times to retain memory.

Most vehicles have one in the trunk, it could be on a side panel. Try your owner's manual. If not there, contact your local Auto Zone and ask them.

Usually the warning light means one of the tail lights or brake lights is out.

YOU MUST CALL JAGUAR AND MAY BE REQUIRED TO TAKE PROOF OF OWNERSHIP WITH VIN NUMBER AND THEY WILL GIVE IT TO YOU...PUT IT IN A SAFE PLACE ONCE YOU GET IT FOR FUTURE NEEDS

This will need to be addressed by the dealership probably need to reset ur computers

Please check all the four wheels, check for dirt on the sensors, check for loose or broken wiring to the sensors. If nons of these are seen on the wheels then it is possible that a sensor is faulty or that the control unit has errors.

p1646 is oxygen censer code, check wire for frays before you replace it

under rear seat

it a sealed transmission, no dipstick.

Hello. Check the fuse. If the fuse looks ok replace it anyway. If that doesn't get em working, check the ground wire for those lights where it attaches to the frame. Remove the screw or bolt or nut there and scrub everything clean with emery cloth then reconnect it. A good ground is critical to good working lights. Joe

4 thumbs up please. ty.