Hyundai Motor 2003 Elantra - Answered Questions & Fixed issues

This is the most likely reason https://www.fixya.com/cars/r29872074-vehicle_cooling_system_no_heat It could also be seized blend door actuators not directing the hot air. Or the switch unit. https://www.google.com/search?q=2003+Hyundai+Elantra+heater+does+not+work ...

Is it possible that the battery isn't fully charged? The interlock is electro-mechanical. Turning the ignition on and putting for foot on the brake should release the shifter lock as you said. For starting issues you need to connect a scan tool and check for DTCs.

On the right side of the ETACS, you will have to feel for an indentation, mine was covered with tape. I peeled it off, then felt the switch within the opening. It slides up and down. With that, I was able to set my new fob. Good Luck.

Replace left front fender - Fixya

www.fixya.com/cars/t26028082-replace_left_front_fender

Dec 29, 2015 - replace left front fender - Hyundai Motor 2003 Elantra question. ...Question about Hyundai Motor 2003 Elantra. Open Question ... How do i remove left front fender clip on a Lincoln ls 2002? Jan 04, 2015 ' 2002 Lincoln LS.

Replace 2003 hyundai elantra front passenger outside door ...

www.fixya.com/cars/t17348691-replace_2003_hyundai_elantra_front

Mar 26, 2013 - Question about Hyundai Motor 2003 Elantra. Open Question.Replace 2003 hyundai elantra front passenger outside door handle. Need to replacebroken exterior door handle on front passenger .... replace left front fender.

3 layer head gaskets torque to 22 ft/lb then 60°-65° then 60°-65°again.
2 layer head gasket torque to 18 ft/lb then 60°-65° then 60`-65° again

It could be a fuel pump issue, try turning the key to the on possition. Do you hear the fuel pump run? It should run for about 3-5 seconds then stop. There should also be a spot on fuel rail to check the fuel pressure.

Wiring, schematic, electrical diagrams, fuse diag, error codes, torque settings etc are basic contents of these online books they have here on this website www.reliable-store.com I have attached. Must check it out

flywheels or flex plates ( manual or automatic) flywheels will generally shatter the bell housing so It may be flex plates They crack the center out from incorrect fitment of the washes at the crank shaft that makes them flex against the torque converter generally it is the omission or the incorrect fitment of the large dish shaped washes or the flex plate not being turn around until all of the bolts screw all the way in finger tight the units are make in thousands and last hundreds of thousands of miles so to have such a problem is lack of attention to detail on fitment or lack of trade skill in the fitting

Either the hose connections are leaking at the rack or the rack is leaking. If you're not seeing any fluid, disconnect one of the bellows at the end of the rack. I bet fluid will pour out

https://www.youtube.com/watch?v=5PQlQ8K2MxU

Does the vehicle have a manual or automatic transmission ? If automatic have you tried moving the gear selector to neutral ? park netural safety switch.

Think your dealer is mistaken. If the engine is stock, then the serial number of car should enable dealer to get the engine info. Try another dealer just to make sure. I NEVER trust those *(&^^^&(*)))&*^%^&(

Turn your headlights on and see if they are nice and brite, and than see if headlights get dim when you try to start the engine.

i think that much damage, qualifies for a total loss

Hey , you know troubled "Strarters" are funny things, "like a broken clock, they are right twice a day !!" There's a little starter drive inside that thing as complicated as he..(you know !!) One thing that I have had the "It doesn't start, it does start bit" from this winter was my battery. I got so ticked that I went & bought a used one from Kijiji for $50. You know what? "It's still in my TRUNK !!!" A lot of places will check your battery for free. Check your battery, it's connections, any acid at the terminals? One tes I have used, for free is "Can you boost another guy's car with your battery, and the car not running?" No Luck, then see about when it's running. When you get into your car, are the "Door ajar" etc. lights bright, or kind of dim compared to when " The Beast" is running? Som e simple tips, maybe not applicable, but come for my favourite price, "FREE". When I'm at a cash & I'm asked "How'd you like to pay sir?" I like to answer "Reluctantly !!" Good Luck ! Geoff

those cars have the filter as part of the fuel pump inside the tank,What you are describing is the lock ring for the fuel pump module that needs removed first then the module can be removed

Youtube has some good how to videos, do a search there. Usually there are two main bolts and the electrical wires that need to be removed.

There are Technical Service Bulletins (TSBs) on many of the Elantras specifically related to hard or abrupt shifting when the transmission or weather is cold. You may need to take it to a Hyundai dealer to ensure the TSBs for the TCM related to shifting have been applied to your particular vehicle.

tcsd and abs work of sensors on all wheels so check for wiring and connections brake light ( on dash) can be low fluid level in the brake reservoir, hand brake still on run the fault codes to find exact codes that are putting the lights on

Have your transmission filter changed and your transmission fluid flushed.