Driver's side door handle recently broke. I can only open the door by rolling down the window and opening it from the outside... If I purchase a replacement door handle, will I have to remove the door panel to replace it or will just unscrewing the current one allow for replacement?
This was a three minute repair, once I had the replacement handle. Leave the door panel alone! Remove the single screw holding the old handle in place. Use a flat blade screwdriver to jimmy the old handle away from the door about an inch. There are two plastic clips holding it to the rods, one for the locking mechanism and one for the latch. Use the flat blade screwdriver to unclip these two connectors. Remove the broken latch, and don't worry, the rods won't disappear into the door! Reverse these steps with the new handle (insert rods, attach clips, wiggle assembly into place, and fasten with single screw). You're done!
Posted on Dec 20, 2009
Have taken my 2000 Hyundai Elantra in for state emissions testing and the results were: On-Board Computer: Unable to test the vehicle because OBD communications could not be established. Vehicle testing site suggested checking the cigarette lighter fuse to see if it was either faulty or blown. Checked the fuse and it appears to be okay.
Any suggestions?
Jim T.
OBD II connector troubleshooting 101
I had the same problem with my 2000 Elantra. the OBD II connector pins get squished and won't make cantact with the scan tool, therefore no connection. the solution is to bend the pins back so they will connect to the scan tool.
FIRST! check your lighter and radio fuses (which you have already done). If possible, make sure your scan tool is working properly, try it on another car. If it is functioning properly, remove the 2 screws holding the obd II connector to the dash. Look for obvious signs of corrosion, damage, or stuff that shouln't be in the connector (rocks, gum, etc.) clean the connector with a good electronics cleaner (I use the CRC stuff), you can usually find it at you local parts store, radio shack, or even wal mart. hose down the inside of the connector thouroughly and allow time to dry.
check for voltage between 4 (gnd) & 16 (+vcc) then 5(gnd) and 16(+vcc) with the ignition on the voltage should be between 12v-16v (these pins may be different on other cars, look for an OBD II connector pinout diagram if your car is different). If this voltage is not present at either pin, the problem is not the connector. check your fuses and wiring. if this voltage is present at both pins continue.
Here's what I did. with the connector free from the dash, you can see the back of the connector where the wires enter the connector. on either side of the connector there may be a white clip. pop both of them off. you should be able to push a small screwdriver or pick in that space to pull the pins back out towards the outside of the connector. do one at a time so you can tell if the pin has moved back out into position. do this for all of the pins. Try to connect. if still no luck try again to push out the pins and reconnect.
If your connection is restored, replace the clips, screw it back into the dash. Return your car to the lousy DMV where they will proceed to tell you something else is wrong which they neglected to tell you on your first 10 visits!! :-)
Stuff thats good to know:
some auto parts stores will connect their OBD II scan tool to you car for free. auto zone is one place
some times the computer will need to reset to restore a connection to the scan tool. to do this simply cycle the ignition off (wait a few seconds) then on again.
online auction places are a excellent resource for USB to OBD II connectors to connect your laptop to your car. there is lots of OBD II diagnostic freeware out there to go with your newly purchased connector.
Good Luck
Chris
-CL Systems
Posted on Feb 06, 2009
Trying to figure out which fuse controls the fuel pump for my Hundai. None of the abbreviations on the fuse box seem to refer to this part.
Posted on Feb 01, 2009
necesito el diagrama de colores de las conecciones de la caja de reles y fusibles, del compartimiento de motor de un Hyundai Elantra SW 1997
Un sitio que tiene mucho informacion sobre diagramas es bulldogsecurity.com Dios te bendiga
Posted on Feb 17, 2009
alarm keep going off what should I do
check door switches,trunk switch,hood switch sounds like dirty contact after you set alarm if any of these contacts lose contanuity your alarm will go off alarm system thinks doors,hood,trunk has been opened
Posted on Feb 07, 2009
My key wont turn in the ignition, and my steering wheel is locked so i cant turn that either.
had the same problem with a 99 dodge van. tow truck driver put the key into the ignition and tapped it a couple of times while turning the key to freed it up and start the engine. works as long as you leave the key in the ignition so i use a second key to lock/unlock the van. hope this works for you. gary
Posted on May 20, 2009
fuse box diagram for 2000 hyundia Elantra
The first picture is the idenification for in the car fuse box. The second is for under the hood.
Posted on Mar 04, 2010
Where is the air bag module located in the 2004 Elantra
the control module is in the center console
Posted on Dec 26, 2010
where is the 2000 hyundai starter located?
Use the jack to lift up the front of the Elantra and place the car on the jack stands. Double-check that the Elantra is secure on the jack stands prior to working underneath the car.
Posted on Oct 29, 2011
2004 Hyundai elantra fuse box diagram
You can check this website you find there fuse box diagram and description for Hyundai Elantra (2005) and others
http://www.autogenius.info/hyundai-elantra-2005-fuse-box-diagram
Posted on Sep 24, 2017
1,531 questions posted
Usually answered in minutes!
1,180 Questions
656 Questions
508 Questions
493 Questions
443 Questions