20 Most Recent 1991 Geo Metro Questions & Answers

A locksmith can come out and make a key for it. But they used to charge $75 just to come out

1991 Geo Metro | Answered on Apr 30, 2017

did you try cranking with throttle open 100%
this clears flooding this cuts the injector(s) dead.
does it/
try fresh spark plugs, are the 10 years old?
try test fuel (spray)? run for 3 seconds,
if not, you lost spark check fuses.
if you have spark and it wants flood is the cam belt 10 years old too, if it slips it will not run again, ever.
until that is cured.

1991 Geo Metro | Answered on Oct 08, 2016

there are 2 hoses,(pair) it's a trans cooler inside the rad.
there is no correct order. it's not polarized in any way.
its just a coil of pipe (atf cooler) inside the rad tank.
if you want it to look stock, the read the shop manual.
it covers this routing, path, and clamps if any.
even the fittings on the rad tank are same sizes, hinting
that either works, ok.

1991 Geo Metro | Answered on Aug 31, 2016

Hi Teresa thats ththhe sign of a battery going bad, how old is the battery? You might want to have it load tested so you can trouble shoot further, there could be more than 1 issue.

1991 Geo Metro | Answered on Jan 09, 2016

you might get lucky with a new PCV valve. But it sounds like you have a small leak in either the intake manifold or a head gasket. if so it will get worse soon. white smoke is water. blue is oil. black is gas. place a white rag or paper towel at the tailpipe to get the true color of the smoke

1991 Geo Metro | Answered on Oct 11, 2015

Yes there is and there pressed in and out

1991 Geo Metro | Answered on Oct 02, 2015

how many , per wheel hub or axle?


in most case there are 2 seals per hub.

but some have an outer bearing with its own seal
so we LOOK first. and is best i all cases.
just read on a real metro forum.
i think yours has 2 seals, early
but what if someone upgrade this hub?
looking always wins.

later axle. #4 is (seal bearing in one) I think yours has 2 seals.


1991 Geo Metro | Answered on Oct 02, 2015

Just install it and the fuel pump will fill it when you start the vehicle.

1991 Geo Metro | Answered on Apr 13, 2015

No this engine is not supposed to be an interference engine.
So you may not have damaged any pistons or valves.

1991 Geo Metro | Answered on Mar 12, 2015

All I can say about this is the transmission is controlled by a cable.
You will have to inspect the cable and the parts to the cable to find what is broken. Wish you luck.

1991 Geo Metro | Answered on Mar 07, 2015

Your probably looking at a transmission rebuild. But it is sporadic. Could be a valve body problem or solenoids. and electrical. Throw it on a scanner and find out.

1991 Geo Metro | Answered on Jan 17, 2015

Several possible causes:
Not enough coolant.
Worn out vanes on the water pump
plugged radiator
bad sensor (is it actually too hot?)
Cooling fan not coming on.
cooling fan shroud broken.
Radiator covered or plugged.
radiator cap not holding pressure
leak in cooling system (water pump shaft seal is a common culprit and hard to spot).

1991 Geo Metro | Answered on Dec 07, 2014

if the covers have screws...remove screws if not you have to take off the rear panel

1991 Geo Metro | Answered on Nov 11, 2014

insert the ECU diagnostic connector (DLC) jumper.
crank for 5 seconds. release key, watch the CEL lamp flash codes.
do you get DTC erropr for the CMP sensor?

which engine>? 1.0L
here is the page that shows HOW TO DO THAT.
this is and OBD1 car, with a jumper check.
all cars , if the precursors to spark fail, sets a code. (error)


1991 Geo Metro | Answered on Sep 30, 2014

get engine hot.
parked, hood up'
now look, its before you eyes where just look.

which engine? 1.0. 1.3L?

1991 Geo Metro | Answered on Sep 14, 2014

relay stuck ,called park relay or as in all electrics
bad wiring
bad control switch to the relay

old post;

1991 Geo Metro | Answered on Sep 09, 2014

Could be either the relay or the horn switch not making contact

1991 Geo Metro | Answered on Aug 24, 2014

we need just 1 clue.
where did you see that.?

1991 Geo Metro | Answered on Jul 29, 2014

try to trace the cable. and then with hands pull it .
or cut it and skin it back and pull the center wire with vise grips.
takes a deft touch to that skin thing, brute force.
getting to the latch and unbolting it from the front, would be hard.
only the trunk monkey can do that.


1991 Geo Metro | Answered on Jul 26, 2014

Not finding what you are looking for?
1991 Geo Metro Logo

158 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1997 Geo Metro
1997 Geo Metro

238 Questions

1995 Geo Metro
1995 Geo Metro

222 Questions

1994 Geo Metro
1994 Geo Metro

197 Questions

1993 Geo Metro
1993 Geo Metro

172 Questions

1996 Geo Metro
1996 Geo Metro

173 Questions

Top Geo Experts


Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Metro Geo

  • Metro Geo

Most Popular Question

outer inner wheel bearing seals front

  • Cars & Trucks