20 Most Recent 2000 Lincoln Navigator Questions & Answers

0helpful
1answer

Subwoofer is not playing

It is hard to say. The sub-woofer has its own amplifier, although it is supplied the sound data from the main amplifier. It could have a problem with the battery power circuit (Sub-Woofer Amplifier Connector Pin 6, LIGHT GREEN/VIOLET) or it could have a problem with the GROUND circuit (Pin 2, BLACK/LIGHT GREEN) Or it could possibly not be receiving the signal from the main amplifier (Pin 7, BROWN/ORANGE "+"), (Pin 8, RED/BLACK "-"). Or it could be that either the sub-woofer speaker is blown, or the sub-woofer amplifier is defective.There is also a "High Audio Mute" circuit that connects between the main amplifier and the sub-woofer amplifier.
7/26/2022 6:10:42 AM • 2000 Lincoln... • Answered on Jul 26, 2022
0helpful
2answers

The air suspension on our 2000 Lincoln navigator seems not to be working right how can we find out what is causing this can we still drive it with this going on?

Ford Air Ride Rear Suspension Down Diagnosis & Fix ...

? 9:57 https://www.youtube.com/watch?v=wfh7n17hvN8 Feb 24, 2014 - Uploaded by FordTechMakuloco Ford Air Ride Rear Suspension Down Diagnosis & Fix ... why theair ride compressor is not turning on and pumping up the air ridesuspension on your truck. ... Ford Expedition & Lincoln Navigator Air Ride C1725 Common Faults ... 2000 Ford Expedition - Replacing the rear shocks with load leveling shocks ...

2003 Lincoln Navigator air suspension fix(3) - YouTube

? 3:41 https://www.youtube.com/watch?v=MhWlcYycny4
3/27/2022 6:22:14 PM • 2000 Lincoln... • Answered on Mar 27, 2022
0helpful
1answer

2000 Lincoln navigator will not start

Presumably you disconnected the battery when you did the fuel pump and PCM? It also looks like the PCM has to be programmed with the VIN Number. https://www.google.com/search?q=2000+lincoln+navigator+pcm To reset the 2000 lincoln navigator anti-theft system press and hold any button on your remote within 20 seconds of the eighth turn. Hold the button for as long as 20 seconds until the locks automatically click and release. Remove the key from the ignition to stop the reset cycle.

How do i perform the 2000 Lincoln Navigator anti theft reset?

More on the anti-theft system https://www.google.com/search?q=2000+lincoln+navigator+security+reset ..
10/30/2021 8:31:21 PM • 2000 Lincoln... • Answered on Oct 30, 2021
0helpful
1answer

My 2000 Lincoln Navigator manual front seat recline lever is stuck in the up position and my seat won't stay in any position how do I fix???

I would remove the seat for easy access to the mechanism so you may see the problem/issue
5/8/2021 2:07:20 PM • 2000 Lincoln... • Answered on May 08, 2021
0helpful
1answer

Remote wire color for lincoln navigator 2000

Check here...

7014902.jpg

Hope thats help (remember rated this).
9/16/2020 2:08:46 AM • 2000 Lincoln... • Answered on Sep 16, 2020
0helpful
1answer

2000 Lincoln navigator sometimes it will start but will not run

If it starts and then dies, check the fuel system. If it runs but will not move check the transmission or a stuck brake system.
1/5/2020 2:23:28 PM • 2000 Lincoln... • Answered on Jan 05, 2020
0helpful
1answer

2000 Lincoln navigator blend door/actuator not enough movement

The door hinge could actually be broken. The door and hinge are all plastic. When you remove the lower console you can actually feel if the door is loose. There is an aftermarket replacement with metal hinges that works great. Normally you have to remove the entire dash to replace or fix it, but the aftermarket one has you go through the glovebox and cut a hole in the duct to reove the old door and replace it with the new one. (You epoxy the cutout back in to seal it - it's out of side and is totally airtight.) I recommend looking into that.
3/16/2019 2:48:10 AM • 2000 Lincoln... • Answered on Mar 16, 2019
0helpful
1answer

My 2000 Lincoln navigator will not start a change this solenoid the starter is good and the battery is good and the fuses are good

If you aren't getting any cranking upon turning the ignition switch it could be the ignition switch itself. If that's the case you'll probably need a locksmith to come over and replace it. But check your service manual for more information first. You might need to do some more troubleshooting.
2/13/2019 9:56:15 PM • 2000 Lincoln... • Answered on Feb 13, 2019
0helpful
2answers

I have a 2000 navigator and it cranks and acts like it wants to start but won't. Sometimes it will start only to drive for a while and then just turn off on you and not come back on for a long time

Sounds like a possible crankshaft sensor, when they start to fail the resistance in the sensor gets too high, sometimes will manage to start but as the temperature of the engine (and in turn the sensor) increases so does the resistance in the sensor and causes an engine cutout, once left to cool down the resitance drops a bit and may allow the engine to start again. This would have to be confirmed with diagnostic equipment or by checking the sensor resistance, either way a job for the garage.
1/30/2019 3:22:54 AM • 2000 Lincoln... • Answered on Jan 30, 2019
0helpful
1answer

Where do I locate the front door fuse for a 2007 Navigator

Go to ford/lincoln owners. Com and register for free then download your owners manual and then go to roadside emergencies and your fuse box diagrams and fuse values are in there
11/24/2018 11:24:21 AM • 2000 Lincoln... • Answered on Nov 24, 2018
0helpful
1answer

I need to replace the heater core in the 2000

You must remove the entire dash from the car to access the heater core. Watch the attached video. https://itstillruns.com/how-to-replace-the-heater-core-in-a-lincoln-navigator-12143658.html
1/2/2018 12:59:38 AM • 2000 Lincoln... • Answered on Jan 02, 2018
0helpful
1answer

2000 navigator won't shift into park

You may have a broken transmission mount take a look put a jack under the tail shaft out a little pressure on it you see it separate if it's bad ..I've also seen motor mounts cause that on rare occasions
12/16/2017 2:46:55 PM • 2000 Lincoln... • Answered on Dec 16, 2017
0helpful
1answer

Key will not turn over

Check to make sure gear shift is in Park. Rock the steering wheel hard without the key in. Try the key...you may have to hold the steering wheel all the way in one direction and try or the other direction and try. Good luck. Sometimes the steering wheel lock does not line up when you removed the key.
10/22/2017 1:59:43 PM • 2000 Lincoln... • Answered on Oct 22, 2017
0helpful
1answer

On my 1999 lincoln Navigator the rear bags are

There may be a switch operated by the hood. I would check the fuses and relays under the hood.
10/6/2017 2:03:55 PM • 2000 Lincoln... • Answered on Oct 06, 2017
0helpful
2answers

2000 navigator: sit higher on one side than the

make sure you don't have an air leak at the springs or the compressor. but you may want to have the air suspension module checked for fault codes. the module itself may be the issue not processing the inputs correctly and mis-leveling the vehicle.
9/25/2017 3:42:24 PM • 2000 Lincoln... • Answered on Sep 25, 2017
0helpful
2answers

2000 navigator: sit higher on

the air ride suspension has level sensors under the vehicle, one of the sensors must be bad making the truck deflate the airbag or inflate it too much. you may need to have someone with a scan tool to access the air suspension module and check for fault codes. you can try turning the air suspension switch off for about an hour to see if the system will reset. the switch is located under the dash on the right side kick panel.
9/25/2017 3:39:46 PM • 2000 Lincoln... • Answered on Sep 25, 2017
0helpful
2answers

Airride suspension won't deflate only inflate

It will only process a "down command" if it thinks all the doors are closed. If you have a bad door switch, it won't lower. Any courtesy lights on with doors closed?
The dealer can conduct a diagnostic scan test and retrieve any codes that will help identify the bad circuit. Did they do that?

Do you have 4 wheel air suspension or just rear?

Assuming rear only:
The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.

Note this section.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).

Air Suspension Switch
The air suspension switch supplies power to the air suspension control module. Without the air suspension control module receiving this power, the load leveling system is inoperative and will not react when the rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off the air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
--------------------------------------------------------------------
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • has a 1,103 kPa (160 psi) internal relief valve.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the air suspension control module determines lowering is required.
  • provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
  • is replaced with the air compressor as a unit.
---------------------------------------------------------------
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing the vehicle and related components.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
---------------------------------------------------
May be a bad module too.
9/25/2017 3:37:35 PM • 2000 Lincoln... • Answered on Sep 25, 2017
0helpful
1answer

On the passenger side for the fuel pump has red on the top on a Lincoln Navigator 2000 and red is that any does it mean it's bad

no that is just there to reset it if is shut down from impact
7/1/2017 3:24:42 AM • 2000 Lincoln... • Answered on Jul 01, 2017
Not finding what you are looking for?

654 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Lincoln Experts

Marvin
Marvin

Level 3 Expert

85240 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22509 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Navigator Lincoln

  • Navigator Lincoln

Most Popular Question

after driving when u put in reverse

  • Cars & Trucks
Loading...