How do you reprogram a key fob for a hyundai coupe. breakdown fixed it for me in less than a minute last week. the guy did something whilst sitting in the drivers seat. it has happened to me again this week and my breakdown service wont come back out as its the same fault as before. There must be a simple way to do it but cant seem to figure it out. please help.
This came directly from my Hyundia service guy:
Unlock the car, get in and close all doors. Turn the ignition key to ACC, press the Unlock button till blinkers flash. That's it. Get out of the car and see if it works.
Posted on Oct 05, 2010
Air bag light is on and stays on. Hyundai had a re-call for this problem where the driver-side seatbelt was affecting the circuit for the airbag. I had the problem checked at a Hyundai dealer (showed them the re-call) and they confirmed that that is cause of the problem and I will have to replace the seat belt (as stated in the re-call). Hyundai Canada is claiming that there isn't any outstanding re-calls for this. My question is, is there a body responsible for dealing with this and how do I contact them?
Posted by BenedictV on
2003 HYUNDAI TIBURON Recall ID from NHTSA: 02V290000
Auto Recall Date:
NOV 05, 2002
SEAT BELTS:FRONT:BUCKLE ASSEMBLY
Estimated Vehicles Affected:
7382 Recall Details
Auto Recall Date: NOV 05, 2002
Vehicle Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Estimated Vehicles Affected: 7382 Model Affected2003 HYUNDAI TIBURON
2003 Hyundai Tiburon Defect Summary:ON CERTAIN PASSENGER VEHICLES, THE DRIVER SEAT BELT BUCKLE WIRING COULD BE DAMAGED BY INTERFERENCE WITH THE DRIVER SEAT CUSHION HEIGHT ADJUSTER MECHANISM.
Defect Consequence:DAMAGED DRIVER SEAT BELT BUCKLE WIRING COULD CAUSE THE SEAT BELT WARNING LAMP OR THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG WIRING LAMP TO ILLUMINATE. IT COULD ALSO CAUSE THE AIR BAG FUSE (CAVITY NUMBER 5) TO OPEN, PREVENTING AIR BAG DEPLOYMENT. NONDEPLOYMENT OF AN SRS AIR BAG IN A CRASH WHERE AIR BAG DEPLOYMENT IS WARRANTED COULD INCREASE THE RISK OR SEVERITY OF INJURY IN A CRASH.
Remedy:DEALERS WILL INSTALL A NEW DRIVER SEAT BELT BUCKLE, IF NECESSARY, AND WILL PLACE A PROTECTIVE COVER OVER THE DRIVER SEAT BELT BUCKLE WIRING TO PREVENT DAMAGE FROM OCCURRING. OWNER NOTIFICATION BEGAN ON MARCH 24, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HYUNDAI AT 1-800-633-5151.
Estimated Vehicles Affected: 7382
Notes: HYUNDAI MOTOR COMPANY 056
Posted on Dec 08, 2008
Serpentine Belt diagram for hyundai tiburon gt 2003
Posted by david... on
2.7 liter engine:
Posted on Nov 20, 2010
On my 2003 tib there are two buttons to work the sunroof... the one that can only lift the roof up and down completely does nothing, no sound, no click, nada. The other that slides the roof back only lifts the roof and slides it half way back. Any ideas??
Posted by wopa20 on
Hi guys you have to re-program the computer function that controls the sun roof. Turn the ignition to off. Hold down both buttons that open the sunroof simultaneously and switch the ignition to on. Continue holding the buttons to open for about 10 seconds, or until you here a click, or until the sunroof opens. This should fix the problem, and remember the solution because it will happen again.
Posted on Dec 07, 2008
my hyundai tiburon has problems starting, some times is starts first time, some times it takes up to five or more goes over an hour to start it. There is no pattern to this issue, happens at random times, its not the battery, what could it be?
It could be several things: A faulty crankshaft position sensor, a problem with the ECU, a bad ground, a faulty mass air flow sensor, faulty camshaft position sensor, a bad fuel pump or fuel pump relay. If you have a large chain type auto parts store ex.(autozone, advanced auto parts, pep boys) nearby, once you get the car started you can go there and they have a diagnostic tool that they will hook up to your car and test it for free, It may read some codes that may pinpoint your problem. If no codes come up, I would be inclined to believe it may be a loose wire or bad ground somewhere.
Posted on Feb 01, 2010
Hyundai getz 7th 2003, want replace stereo, whats the best solution.?
do i need the remove the whole face around stereo and buttons etc.and how?
and once i removed that what is the wiring diagram?
pictures will be very helpful
Posted by philtan866 on
Here's a pic
Pops out, then remove 4 screws which mount the audio & instrument panel.
Posted on Jun 05, 2009
diagnostic codes p1505 p1507 ran stalled wont run turns over fine
change crank position sensor and blown ecm 15amp fuse
Posted on Feb 29, 2012
the passenger exterior door handle is broken off. How do I replace it?
Posted by bedleman on
inside door panel has to come off, then there are usually 1 rod on the handle pull, and one rod on the lock.. these pop off the rod and stay on the hanldle body. there should be @ 3 or 4 nuts on the back side of the handle. thease removed and the old handle shouold pop out.. dont force it... new handle in... .hand snug the nuts, put op rods back in proper holes, snap in clips... TEST BEFORE YOU PUT THE DOOR PANEL BACK ON...... saves lots of time if you happen to put the rods in wrong.
Posted on Mar 06, 2011
how do i chage a c/v axle on a hyundai tiburon
Posted by manuel124 on
Specifically for 2003 Tiburon V6 6 speed, but may work for you as well.
-Loosen tire lugs
-Remove center caps with screw driver or similar tool (careful not to scratch caps)
-loosen axle nut
-Jack the car up and place on jack stands
-Chalk rear wheels
-finish removing tire lug nuts and tire
-remove cotter pin and finish removing axle nut
-remove brake pads
-remove caliper and brake assembly
-remove rotor (possible PITA), use extreme caution hammering a stuck rotor!
*remove 2 bolts from strut mount assembly. This will allow you enough clearance to "cleanly" pull axle out with minimal force/hammering. No axle puller tool necessary and no messing with the lower ball joint.
-Now gently tap the axle out of the hub assembly
-pull the rest of the axle out of the hub assembly by hand or pry with long screw driver or pickle fork. Again, since you removed the 2 strut assembly bolts, your hub assembly should have dropped down and away from the axle quit a bit to allow you enough clearance to remove axle from hub assembly
**Follow next steps for DRIVER SIDE ONLY**
-Next, place a fluid pan to catch any leaking trans fluid before removing axle from transmission side.
-Using a long screwdriver or pickle fork, pry the axle away from the transmission
-Remove entire axle and replace with new one
-Installation is reverse of removal steps. (not difficult, just line up the splines and everything should "pop" in place
Posted on Sep 12, 2010
Got an OBD 11 and checked it for a code and the code that came up is:
Evaporative Emmission Control System Leak Detected (Gross Leak)
What do I do now and what does this mean exactly, what is wrong with the car and what parts does it need to be fixed and an approximate cost and time labour should take
Posted by klfedak on
Well actually this is the most embarasing code to get... It actually means your emission purge line is inoperative. Yes your scanner told you a generic definition, which is the nature of OBD 2 but, the truth is that 10 out of 10 times this code will not be fixed by replacing the gas cap. This particular code relates to any one of 3 components, and two sensors in your evap system. Test the sensors, and if they are good, then have your evap canister weighed. If it is the correct weight, then don't replace it, check the valve on the purge line, if that is fine then you have to replace the filler neck. Not because the filler neck is bad, but because there is a filter made into it which is connected to the purge line which is plugged with charcole and fuel, and this is where it gets embarasing... Its plugged because you over filled your tank too many times. Letting the pump go until it shuts its self off is very easy, but also very costly. As you have just found out.
Posted on Apr 29, 2009
1,337 questions posted
Usually answered in minutes!
Step 2: Please assign your manual to a product: