20 Most Recent
1996 Eagle Vision - Page 5 Questions & Answers
Blue book value
on what type vehical also can check kelly blue book on line google it
Noise from defferencial
on my 1981 corvette I changed my gear oil & in a parking did 8 figure 8s and the noise was gone
The motor wont crank over
test for fire at the coil then if you have it there check each cylinder. if that dont work take off the intake hose spay ether in it then try to start
Battery is overcharging on 94
Test it with a multi meter set to d.c voltage. with the car running it should be between 12.5 and 14.5 volts. If it is not replace the voltage regulator.(sometimes it is a parts of the alternator and in your case it is) ECH VR578 would be the napa part number for it
My hp system has slow
what operating system do u use? have u done a system harddrive fragment? have you cleared the short term memory with the disk clean tool? run a virus and malware test scan? if not do the about services and see if the speed comes up, also dump any program's u no longer use.
Battery won't stay charge and
It sounds to me like you have a LOAD on your Electrical System that is draining the Battery. Sometimes it turns out to be a Light that somehow isn't turned off, in other cases, it can be corroded wiring and connections covered with conductive dirt which can pull several Amperes load. Have your vehicle checked out by a Certified Mechanic that specializes in Electrical Problems.
Fastest Robe
Where is #1 cylinder and
There were 2 engines in the Vision line, here are both.
3.3 liter V-6 VIN "T"
3.5 liter SOHC V-6 VIN "F"
It appears they both us
e the same coil setup and firing order.
How to Replace Door Locks in Eagle Vision ?
The procedure to replace the door locks in car is as follows:--
1) First of all carefully remove the arm rest and any speaker covers if speakers are connected.
2) Then remove the door panel. The door panel is connected by plastic clips.
3) Then remove the door handle screws with the help of screwdriver.
4) After the screws are removed the door handle will come out
5) Now the interior doors handle needs to be removed. the interior door handle is fitted by plastic clips you can use a pliers to pop out the plastic clip, then twist the clip to allow the interior door handle to swing free and easily come out.
6) Take the door handle out
7) Now in the door remove the rod from lock core.Then remove the two bolts holding the door handle assembly.
8) Now before removing the old door lock, please take note of the position in which it is placed. So while inserting new lock there is no problem about placing the new lock.
9) Insert the new lock carefully to the proper position. And reverse/refit all the parts which you removed while replacing the old door lock.
This will help. Thanks.
RPM's are fluctuating while driving. Turns over,
Sounds like you either need to reolace the crank sensor or the camshaft speed sensor,depending on which your engine comes with.If you tach doesn't get a signal then neither does the engine controller and it is like you are not even trying to start the car although you are in fact turning the key and cranking the engine.
How to Change Thermostat in Eagle Vision car?
1) First buy a new thermostat for you car year and model.
2) Then as per the procedure. Remove the radiator cap. Be careful that there will be pressure in the radiator. So just let the pressure release first before removing the cap completely.
3) The thermostat is connected to the black hose coming from radiator.
4) On the top of the engine there will be thermostat cover. The cover is fitted by two bolts on each side.
5) Then remove the hose connected to radio with the help of a pier.
6) The other end of the hose is connected at thermostat cover. Carefully remove the other end of the hose. A bit of coolant will flow from the hose while removing the hose.
7) Remove the screws holding the thermostat cover. Lift the cover after the screws are takes out. Then take the thermostat seated under the cover.
8) Remove the old gasket out from the thermostat with the help of knife.
9) Before removing the old thermostat carefully notice the position of old thermostat. In the same way place the new thermostat with the spring assembly in the down side of the engine.
10) Refit all the parts removed while removing the old thermostat properly.
11)After every thing is fitted proper as it was before, then check the coolant level if its low get it refilled till the required level.
This will help. Thanks.
Not finding what you are looking for?
